eng
Clean plastic parts (e.g. housing) only with REMS CleanM machine cleaner
(Art. No. 140119) or a mild soap and a damp cloth. Do not use household
cleaners. These often contain chemicals which can damage the plastic parts.
Never use petrol, turpentine, thinner or similar products for cleaning.
Make sure that liquids never get onto or inside the power tool. Never immerse
the power tool in liquid.
5. Faults
5.1. Fault: Power tool does not start.
Cause:
● Worn carbon brushes.
● Mains lead defective.
● Power tool defective.
5.2. Fault: Drive unit will not rotate under load.
Cause:
● Worn carbon brushes.
● Tools not greased suffi ciently.
● Setting wheel on the safety inching switch (fi g. 2 (6)) not set correctly.
● Pipe wall too thick.
● Pipe material too hard.
5.3. Fault: Expansion/widening too narrow.
Cause:
● Expander mandrel/widening tool worn.
6. Disposal
The REMS Twist / Hurrican drive unit may not be thrown in the domestic waste
at the end of use. It must be disposed of properly by law.
7. Manufacturer's Warranty
The warranty period shall be 12 months from delivery of the new product to the
fi rst user. The date of delivery shall be documented by the submission of the
original purchase documents, which must include the date of purchase and the
designation of the product. All functional defects occurring within the warranty
period, which are clearly the consequence of defects in production or materials,
will be remedied free of charge. The remedy of defects shall not extend or
renew the warranty period for the product. Damage attributable to natural wear
and tear, incorrect treatment or misuse, failure to observe the operational
instructions, unsuitable operating materials, excessive demand, use for unau-
thorized purposes, interventions by the customer or a third party or other
reasons, for which REMS is not responsible, shall be excluded from the warranty
Services under the warranty may only be provided by customer service stations
authorized for this purpose by REMS. Complaints will only be accepted if the
product is returned to a customer service station authorized by REMS without
prior interference and in a fully assembled condition. Replaced products and
parts shall become the property of REMS.
4.2. Inspection/Servicing
WARNING
Pull out the mains plug before maintenance and repair work! This work
may only be performed by qualifi ed personnel.
The gear runs in a life-long grease fi lling and therefore needs no lubrication.
The motor of the power tool has carbon brushes. These are subject to wear
and must therefore by checked and changed by qualifi ed specialists or an
authorised REMS customer service workshop from time to timentre.
Remedy:
● Have carbon brushes changed by qualifi ed technical personnel or an
authorised REMS customer service workshop.
● Have the connecting cable changed by qualifi ed technical personnel or an
authorised REMS customer service workshop.
● Have the mains lead changed by qualifi ed personnel or an authorised REMS
customer service workshop
Remedy:
● Have carbon brushes changed by qualifi ed technical personnel or an
authorised REMS customer service workshop.
● Lightly grease the expanding mandrels and neck widening tools with the
lubricant provided (Art. No. 151240).
● Adjust the setting wheel on the safety inching switch according to the table.
● See 1. for permissible pipes. Technical data / 1.3. Applications
● See 1. for permissible pipes. Technical data / 1.3. Applications
Remedy:
● Replace expander mandrel/widening tool.
The user shall be responsible for the cost of shipping and returning the product.
A list of the REMS-authorized customer service stations is available on the
Internet under www.rems.de. For countries which are not listed, the product
must be sent to the SERVICE-CENTER, Neue Rommelshauser Strasse 4,
71332 Waiblingen, Deutschland. The legal rights of the user, in particular the
right to make claims against the seller in case of defects as well as claims due
to wilful violation of obligations and claims under the product liability law are
not restricted by this warranty.
This warranty is subject to German law with the exclusion of the confl ict of laws
rules of German International Private Law as well as with the exclusion of the
United Nations Convention on Contracts for the International Sales of Goods
(CISG). Warrantor of this world-wide valid manufacturer's warranty is REMS
GmbH & Co KG, Stuttgarter Str. 83, 71332 Waiblingen, Deutschland.
8. Spare parts lists
For spare parts lists, see www.rems.de → Downloads → Parts lists.
eng
9