Before Use; Installation Sequence; Included In Delivery; Installation Instructions - Starmix airstar TT1800 Instrucciones De Montaje

1 Before use

We have compiled these operating instructions so that you become
familiar with your new appliance quickly and comprehensively.
● Please read these instructions carefully before using this
appliance. It provides you with important information on its
safety, operation, maintenance and disposal.
● Familiarise yourself with your new appliance and its various
functions following the sequence of the instructions.
● Follow all notes and explanations referring to the correct
operation and handling. This will ensure the continuous
availability and a long life for your appliance.
● The safety notes, in particular, must be followed. They help
you to prevent accidents and to protect your appliance from
damage.
● Please keep these instructions for future reference.
This appliance complies with the current state of technology and
the applicable safety regulations for electrical appliances. The
manufacturer will not accept any liability for damage caused by
improper use or incorrect operation.

2 Included in delivery

1 hair and/or hand dryer
4 dowels
4 button head wood screws
1 terminal
2 countersunk flat head tapping screws for cover plate
2 strain relief clamps
4 slotted pan head screws for strain relief clamps

3 Installation instructions

The installation must be carried out by qualified personnel to
ensure that the appliance is connected in accordance with safety
regulations. In rooms with showers and bath tubs the appliance
must be installed with the minimum distances laid down in the VDE
regulations (0.6 mtrs (24 inches) from the edge of the shower and/
or bath and 1.2 mtrs (48 inches) from a shower head).
Original operatin instructions in German

3.1 Installation sequence

The maintenance-friendly installation concept
The TT1800 / T 500 E installation system enables simple,
maintenance-friendly wall mounting without having to open up
the appliance. For ease of installation, we have separated the
appliance into two components: The installer installs a socket (or a
permanent connection), screws the mounting plate on, slides the
ready-to-use appliance onto it, inserts the mains plug into the so-
cket (or connects), screws the anti-theft cover plate on – finished.
It's as easy as that!
4. Pull the cover plate [ 1 ] (not screwed on) down and out of the
appliance. Pull the mounting plate [ 2 ] which has been inserted
at the back of the appliance downwards and out.
5. Confirm where the appliance is to be located, mark the 4 fixing
holes [ 12 ], using mounting plate [ 2 ] as a template, drill the
holes (8 mm Ø), insert the dowels and fix the mounting plate
with the enclosed button-head wood screw A. We recommend
mounting heights as shown in figures A, B or C. It must be
ensured that the appliance is firmly secured to a solid wall.
6. There are 5 different ways to connect the appliance as descri-
bed below.
● Mounting via an installed flush socket.
The upper part of the cover plate [ 1 ] is not required. Break it
off at the predetermined breaking point [ 4 ]. When the moun-
ting plate [ 2 ] has been fixed, push the appliance onto to the
mounting plate from the top as shown in figure B , insert the
plug into the socket [ 3 ] und push the appliance all the way
down. Fasten the cover plate with the 2 enclosed countersunk
flat head tapping screws.
● Concealed wiring.
Connection via wiring concealed in the wall [ 7 ](instead of
a socket). Fix mounting plate [ 2 ] to wall as shown in fig.
C. Slide the cover plate into the mounting plate from below
and route the wiring from the wall through the opening in the
cover plate. Insert the attached terminal [ 11 ]. Cut the plug
at the connection lead [ 5 ] of the appliance, strip the cable
and, squeeze the wire end ferrules on. Connect both lead as
shown in fig. C. Ensure that L (brown) and N (blue) are con-
nected correctly. Secure the connecting lead of the appliance
with the enclosed strain-relief clamp [ 8 ]. Push appliance
fully down onto the cover plate and screw in the 2 enclosed
countersunk flat head tapping screws.
● Surface mount wiring from above
Break out the wiring lead through at the rear of the appliance,
top centre. When the mounting plate [ 2 ] has been attached
as shown in fig. C, route the surface mount wiring on the
mounting plate down under the cover plate [ 1 ] and through
GB - 23