CONTROL SET-UP PROCEDURES
IMPORTANT: Read all instructions before operating.
The lower fabric setting key pads and the digital display are
used to set up the controls. The display can contain 4 numbers
and/or letters and a decimal point. These are used to indicate
the set-up codes and related code values available for use in
programming the washer.
How to use the key pads to p;rogram the controls
1. The LOWER LEFT key pad is used to adjust the values
associated with set-up codes. Pressing the key pad will
increment the value. Rapid ajustment is possible by holding
down the key pad.
2. The LOWER MIDDLE key pad will advance you through the
set-up codes. Pressing the key pad will advance you to the
next available set-up code. Holding down the key pad will
automatically advance through the set-up codes at a rate
of one (1) per second.
3. The LOWER RIGHT key pad is used to select or deselect
options.
Start Operating Set-Up
PD Models: Insert access door key, turn, and lift to remove
n
access door.
PR Models: Once the debit card reader is installed (according
n
to the reader manufacturer's instructions), the set-up mode
can be entered by inserting a set-up card (supplied by the
reader manufacturer) into the card slot. If a manual set-up
card is not available, manual set-up mode can be entered
by removing connector AA1 on the circuit board.
IMPORTANT: The console must not be opened unless power
is first removed from the washer. To access connector AA1:
g Unplug washer or disconnect power.
g Open console, disconnect plug on AA1, close console.
g Plug in washer or reconnect power.
The washer is now in the set-up mode.
NOTE: The control does not need to be set up in order for
the washer to operate. These procedures are to be followed
only to customize the control as desired.
SET-UP CODES
The LOWER MIDDLE key pad will advance from code
n
to code.
The LOWER LEFT key pad will change the code value.
n
The LOWER RIGHT key pad will select or deselect options.
n
FOR PR MODELS: The set-up codes are the same as for the PD
models, except where noted.
The set-up code is indicated by the one or two left-hand
characters. The set-up code value is indicated by the two
or three right-hand characters.
CODE
REGULAR CYCLE PRICE
6.07
Represents the number of coins (coin 1); may adjust
6.07
from 0–39. (See VALUE OF COIN 1.) Advance from
0–39 by pressing the LOWER LEFT key pad. Factory
preset for 7 coins = $1.75.
PR MODELS ONLY: Factory preset for 0 coins.
g Press the LOWER MIDDLE key pad once to advance to next code.
10
EXPLANATION
CODE
WASH LENGTH
7.11
This is the number of minutes for WASH.
7.11
Choose from 8–20 minutes by pressing the LOWER
LEFT key pad.
g Press the LOWER MIDDLE key pad once to advance to next code.
RINSE CYCLES
8.21
This is the length and total number of rinses. Each
8.21
rinse agitation is 1–4 minutes, with a choice of 1
or 2 rinses. The middle digit is the length of rinse
agitation and the right digit is the number of rinses.
The number is changed in the following sequence
(11, 21, 31, 41, 12, 22, 32, 42) by pressing the
LOWER LEFT key pad.
Press the LOWER MIDDLE key pad once to advance
to next code.
The DELICATES & KNITS cycle has a fixed rinse
agitation length of one minute.
g Press the LOWER MIDDLE key pad once to advance to next code.
CYCLE COUNTER OPTION
9.00
This option is either SELECTED "ON" or NOT
SELECTED "OFF."
Not Selected "OFF."
9.00
Selected "ON" and not able to be deselected.
9.0 C
Press the LOWER RIGHT key pad 3 consecutive
times to select "ON." Once selected "ON" it cannot
be deselected.
g Press the LOWER MIDDLE key pad once to advance to next code.
MONEY COUNTER OPTION
1.00
This option is either SELECTED "ON" or NOT
SELECTED "OFF."
Not Selected "OFF."
1.00
Selected "ON."
1.0 C
Press the LOWER RIGHT key pad 3 consecutive
times to select "ON" and 3 consecutive times to
remove (Not Selected "OFF.") Counter resets by
going from "OFF" to "ON."
Selected "ON" and not able to be deselected.
1. C 0
To select "ON" and not able to be deselected, first
select "ON," then within two seconds press the
LOWER RIGHT key pad twice, the LOWER LEFT
key pad once, and exit the set-up mode.
g Press the LOWER MIDDLE key pad once to advance to next code.
SPECIAL PRICING OPTION
2.00
This option is either SELECTED "ON" or NOT
SELECTED "OFF."
Not Selected "OFF."
2.00
Selected "ON." Press the LOWER RIGHT key pad
2.5 P
once for this selection.
If SPECIAL PRICING OPTION is selected, you have access
to codes "3." through "9.".
g Press the LOWER MIDDLE key pad once to advance to next code.
OPTIONS TO USE IF SPECIAL PRICING IS SELECTED:
SPECIAL CYCLE PRICE
3.07
Represents the number of quarters (coin 1): may
3.07
adjust from 0–39. (See VALUE OF COIN 1.) Advance
from 0–39 by pressing the LOWER LEFT key pad.
Factory preset for 7 coins = $1.75.
PR MODELS ONLY: Factory preset for 0 coins.
g Press the LOWER MIDDLE key pad once to advance to next code.
EXPLANATION