Electrical Connection; Accessories - DeWalt DW717 Manual De Instrucciones

• TURN OFF THE MACHINE and allow the blade to come to a complete stop before
raising the arm and prior to cleaning the blade area, removing debris in the path of the
blade, before servicing or adjusting tooL A moving blade can cause serious injury.
• PROPERLY SUPPORT LONG OR WIDE WORKPIECES. Loss of control of the
workpiece can cause injury.
• NEVER cross arms in front of blade while using tooL Always make a dry run
(unpowered) before making a finish cut so that you can check the path of the blade or
severe personal injury may result.
• ADDITIONAL INFORMATION regarding the safe and proper operation of power
tools (i.e. a safety video) is available from the Power Tool Institute, 1300 Sumner
Avenue, Cleveland, OH 44115-2851 (www.powertoollnstitute.com). Information is
also available from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL
60143-3201. Please refer to the American National Standards Institute ANSI 01.1
Safety Requirements for Woodworking Machines and the U.S. Department of Labor
OSHA 1910.213 Regulations.
A CAUTION: Do not connect unit to electricalpower source until complete instructions are
read and understood.
,&WARNING: Always wear proper personal hearing protection that conforms to
ANSI $12.6 ($3.19) during use. Under some conditions and duration of use, noise from
this product may contribute to hearing loss.
WARNING: NEVER MAKE ANY CUT UNLESS THE MATERIAL IS SECURED ON
THE TABLE AND AGAINST THE FENCE.
_},WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber (CCA).
Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: work in a well ventilated area, and work
with approved safety equipment, such as those dust masks that are specially designed to
filter out microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding,
drilling, and other construction activities. Wear protective clothing and wash
exposed areas with soap and water. Allowing dust to get into your mouth, eyes,
or lay on the skin may promote absorption of harmful chemicals.
_ WARNING: Use of this tool can generate and/or disburse dust, which may cause
serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved
respiratory protection appropriate for the dust exposure. Direct particles away from face
and body.
For your convenience and safety, the following warning labels are on your miter saw.
ON MOTOR HOUSING:
A WARNING: FOR YOUR OWN
SAFETY, READ INSTRUCTION
MANUAL BEFORE OPERA TING SAW.
WHEN SERVICING, USE ONLY
IDENTICAL REPLACEMENT PARTS.
DO NOT EXPOSE TO RAIN OR USE IN
ALWAYS ADJUST FENCE PROPERLYBEFORE USE.
CLAMP SMALL PIECES BEFORECUT[IN6. SEE MANUAL.
AJUSTE LA GUiA DEBIUAMENTE ANTES DE UTiLIZAR LA
HERRAMIENTA. ASEGURE LAS PIEZAS PEQUENAS ANTES DE
CORTARLAS. CONSULTE EL MANUAL.
TOUJOURS REGLER LE GUIDE AVANT L'UTILISATION. FIXER LES
PETITS ORJETS AVANT DE LES SCIER. CONSULTER LE GUIDE
D'UTILISATION.
J
DAMP L OCA TIONS.
AL WAYS WEAR EYE PROTECTION.
ON MOVING FENCES:
ALWAYS ADJUST FENCE PROPERLY BEFORE USE. Clamp small pieces before
cutting. See manual
ON GUARD: DANGER - KEEP A WAY FROM BLADE.
_EEP AWAY
ON UPPER GUARD: PROPERLY SECURE BRACKET WITH BOTH .........
M_N_ENERS AL_JAO0
SCREWS BEFORE USE. D ......
S'_LOIGNE_ DEL_LAthE
ON TABLE: (2 PLACES)
AL WAYS TIGHTEN ADJUSTMENT KNOBS BEFORE USE.
KEEP HANDS 6" (152.4 MM) FROM PATH OF SAW BLADE.
NEVER PERFORM ANY OPERA TION FREEHAND.
NEVER CROSS ARMS IN FRONT OF BLADE.
THINK! YOU CAN PREVENT ACCIDENTS.
DO NOT OPERATE SAW WITHOUT GUARDS IN PLACE.
TURN OFF TOOL, KEEP SAW HEAD DOWN AND WAIT FOR SAW TO
STOP BEFORE MOVING HANDS, WORKPIECE OR CHANGING
SETTINGS.
UNPLUG TOOL BEFORE CHANGING BLADE, MOVING OR SERVICING
UNIT.
Electrical Connection
Be sure your power supply agrees with the nameplate marking. 120 volts, AC means that
your saw will operate on alternating current. The switch is suseptible to failure if direct
current is used. A voltage decrease of 10 percent or more will cause a loss of power and
overheating. All DEWALT tools are factory tested. If this tool does not operate, check the
power supply.
Accessories
Recommended accessories for use with your tool are available for purchase from your local
dealer or authorized service center. If you need assistance in locating any accessory for
your tool, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD
21286, call 1-800-4-DEWALT (1-800-433-9258) or visit our website www.dewalt.com.
,_ WARNING: Since accessories, other than those offered by DEWAL T, have not been
tested with this product, use of such accessories with this tool could be hazardous. To
reduce the risk of injury, only DEWAL T, recommended accessories should be used with
this product.
Optional Accessories
The following accessories, designed for your saw, may be helpful. In some cases, other
locally obtained work supports, length stops, clamps, etc., may be more appropriate. Use
care in selecting and using accessories.
Laser Guide System: DW7187
Powered by the saw, the bright laser line delivers enhanced visibility in low and high
light locations. Easy to install.
Extension, Work Support: DW7080
Used to support long overhanging workpieces, the work support is user assembled.
Your saw table is designed to accept two work supports; one on each side.
Clamp: DW7082 (similar model included)
Used for firmly clamping workpiece to the saw table for precision cutting.
Dust Bag: DW7053 (Included with some models)
Equipped with a zipper for easy emptying, the dust bag will capture the majority of the
sawdust produced (not shown).