Antenna Setup And Channels Search; Basic Mode - Tele System TS3002 Manual De Uso

TELE System

3.2.1.2 Antenna setup and channels search

CAUTION!
The My Dish menu settings are specific to your antenna plant. Any wrong settings may make it impossible to view
certain TV programs. It is important that you know the characteristics of your antenna plant and/or consult a professional
installer in order to correctly setup the receiver.
Modifying the Switch Type parameters, to either NONE, DiSEqC 1.0 or DiSEqC 1.2/USALS, presents three
different configuration modes.
3.2.1.2.1

Basic Mode

Single LNB/satellite antenna plants, with a direct connection between the receiver and antenna, do not use
DiSEqC or other specific communication protocols.
Antenna and satellite setup
Use the following settings for the first two parameters:
x
Switch type: None
x
Toneburst: Off
At the third parameter, press OK and the Edit parameters screen will appear:
Satellite Name: Select satellite name. Press the RED Add SAT button, select the satellite and press
1.
OK. (i.e. HotBird 13°E)
LNB Type: Antenna converter. Change the LNB type using
2.
Universal)
LNB Low/High Freq: Local oscillator frequency
3.
22K Tone: 22KHz signal to switch between high and low frequency bands.
4.
Power: Power control for switching H/V polarity
5.
Transponder: TP frequency on which to mount the antenna to receive the signal; Strength and Quality
6.
indicators are shown on screen. Use
available as a result of the previously selected satellite
CAUTION!
If the signal Strength and Quality bars at the bottom of the screen do not respond or indicate low levels, make sure the
parameters have been entered correctly and that the selected TP is not out-of-date.
x
Press OK to save settings and return to the previous screen
Satellite channels scan
To conduct a channel scan on a selected satellite:
x
Press the BLUE Scan button
x
Define the following in the Scan mode screen:
Scan Mode: scan the Transponder database (Default) or by a Blind-scan (Blind-Detail)
1.
Programme: choose Free Only to scan only free channels (recommended) or All for coded channels as
2.
well
x
Press OK to start scan
3.2.1.2.2 DiSEqC 1.0 Mode
The DiSEqC 1.0 protocol was developed for multiple converter antenna plants and allows switching between
up to four satellite sources.
Use the following settings for the first two parameters:
x
Switch type: DiSEqC 1.0/1.1
x
Toneburst: Off
Press OK for each of the four LNB1÷LNB4 items and a Edit screen will appear for each satellite:
Satellite Name: Select satellite name. Press the RED Add SAT button, select the satellite and press
1.
OK. (i.e. Dual-feed: HotBird 13°E on LNB1 and Astra 19.2°E on LNB2)
LNB Type: Antenna converter. Change the LNB type using
2.
Universal)
LNB Low/High Freq: Local oscillator frequency
3.
22K Tone: 22KHz signal to switch between high and low frequency bands
4.
LNB Power: Power control for switching H/V polarity
5.
Transponder: TP frequency on which to mount the antenna to receive the signal; Strength and Quality
6.
indicators are shown on screen. Use
available as a result of the previously selected satellite
CAUTION!
If the signal Strength and Quality bars at the bottom of the screen do not respond or indicate low levels, make sure the
parameters have been entered correctly and that the selected TP is not out-of-date.
x
Press OK to save settings and return to the previous screen
12
/ to choose a transponder from the list of transponders
/ to choose a transponder from the list of transponders
/ . (i.e. In Italy, a typical setting is
/ . (i.e. In Italy, a typical setting is