Cleaning And Maintenance; Technical Data - stayer SC210W Manual De Instrucciones

Proceed as described for sawing straight cross-cuts in the
cut-off saw position.
For sawing mitre cuts in the table saw position, proceed as follows:
Set the guide fence (17) for sawing mitre cuts.
Proceed as described for sawing straight cross-cuts in the
table saw position, starting in point 2.
Sawing bevel cuts (fig. L)
Bevel cuts are performed with the machine set up in the cuf-off
saw position. While sawing bevel cuts, the workpiece is placed
against the fence (13) and sawn through at an inclination.
Set the bevel angle.
Proceed as described for sawing straight cross-cuts in the
cut-off position.
Sawing compound mitre cuts (fig. F - M)
Compound mitre cuts are performed with the machine set up in
the cuf-off saw position. While sawing compound mitre cuts,
the workpiece is placed against the fence (17) and sawn through
in a combined mitre and bevel cut.
Set the mitre angle.
Set the bevel angle.
Proceed as described for sawing straight cross-cuts in the
cut-off position.
Mounting and adjusting the table extenders
Using the table extenders (41) you can support long workpieces.
The table extenders can be mounted both to the left and to the
right of the machine.
Insert on each side a table extender (41) into the openings in
the base of the machine as shown.
Dust extraction (fig. O)
The dust extraction outlet together with an external vacuum
cleaner takes care of the dust extraction of the working surface.
Place the adapter (42) on the dust extraction connection (5).
Connect a vacuum cleaner to the machine.
We recommend at least 1500W vacuum with automatic start.

CLEANING AND MAINTENANCE

The machine does not require any special maintenance.
Regularly clean the ventilation slots.
Remove all dust from the housing.
Regularly check the machine for possible damages.
Before use always check the state of the saw blade.
Particularly make sure that the saw blade is fastened firmly
and that there is no play on it.
Before use always check the distance between riving knife and
saw blade and between guard and saw blade.

TECHNICAL DATA

Power input
No load speed
Blade size
Weight
Cutting capacity:
- Cross cut at 90º
- 45º mitre cut
- 45º bevel cut
- Compound mitre cut 45º- 45º
- Skirting board cut at 0º
- PVC pipes
- On upper table
The values given are valid for nominal voltages [U] of
230/240 V ~ 50/60 Hz - 110/120 V ~ 60 Hz. For lower
voltage and models for specific countries, these values
can vary.
ENGLISH
21
1200 W
-1
4500 min
ø 210 x 30 x 2,5 mm
12 kg
b x h
120 x 55 mm
65 x 55 mm
120 x 35 mm
40 x 23 mm
20 x 70 mm
Ø 70 mm
0 - 33 mm
21
Please observe the article number on the type pl ate of your
machine. The trade names of the individual machines may
vary.
Level of sound pressure measured according to
EN 61029-1:2000:
( sound pressure )
L
pA
L ( acoustic power )
WA
Take appropriate measures for the protection of
hearing.
The sound levels stated are emission levels; they are not
necessarily safe working levels. Even though the measured
values are related to exposure levels, this information does not
allow to determine if additional measures are required.
Factors that can affect the radiated levels are duration of
exposure, the characteristics of the work area and other sound
sources, as well as the number of machines of the same type or
other machines in the work area. The acceptable exposure levels
may differ according to the country of use.
This information is only intended to help the user assess
possible risks.
GUARANTEE
Refer to the enclosed guarantee conditions for the terms and
conditions of guarantee.
Repair service
Our after-sales service responds to your questions concerning
maintenance and repair of your product as well as spare parts.
Exploded views and information on spare parts can also be found
under: info@grupostayer.com
Our customer consultants answer your questions concerning best
buy, application and adjustment of products and accessories.
Disposal and recycling
The machine, accessories and packaging should be sorted for
environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools into household waste!
According the European Guideline 2002/96/EC for
Waste Electrical and Electronic Equipment and its
implementation into national right, power tools that
are no longer usable must be collected separately and
disposed of in an environmentally correct manner.
Subject to change without notice.
SC210W
92,5 dB(A)
99,7 dB(A)