Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
8) SWR ADJUSTMENT
adjust
This function allows to
the SWR (Standing Wave Ratio) by beep tones.
Press PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use the UP/DN buttons (18) on the micro-
phone to
select
the SWR function.
2.
Press the rotary PUSH knob (6). The radio automatically
without pressing PTT switch (17) . The SWR measurement starts. Measurement
time is 5 minutes maximum. The remaining time is displayed.
3.
Adjust your antenna.
4.
The beep tone* is continuous when SWR value is equal to 1. 0 . The delay
between two beeps becomes longer when SWR value moves away from1. 0 .
Display shows the SWR value. For example 2. 5 .
5.
Press PTT switch (17) to
exit
MENU mode.
*The volume of the beep tone is adjustable with VOLUME knob (1). Please
check that the beep volume is set to a comfortable listening level.
See § HOW TO ADJUST SWR page 21.
9) MIC TYPE
The PRESIDENT RICHARD can be used with an electret microphone as well
as with the dynamic one, 6-pin PRESIDENT (see the cabling diagram page
74). Turning on the unit, the type of the microphone is briefly displayed.
Press PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
select
to
the MIC TP function.
2.
Press PUSH knob (6) to
validate.
3.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
the type on the microphone EL (electret) or DY (dynamic).
4.
New press on PUSH knob (6) to validate. The parameter stops blinking. a)
Go back to point 1 to
adjust
another function or b) Press the PTT switch (17)
to
validate
and
exit
MENU.
5.
exits
If no key is pressed, the unit
the display.
Default type of microphone is EL (electret).
10) PA SETTING
This function allows to
select
the operating mode of Public Address.
Press PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
the PA SET function.
2.
Press PUSH knob (6) to
validate.
enter
MENU.
is displayed.
goes
to
disappears on the display.
enter
MENU.
is displayed.
The current parameter blinks on display.
disappears.
MENU after 10 seconds,
disappears on
enter
MENU.
is displayed.
The current value blinks on display.
3.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
select
to
the operating mode of the PA : I n, OF or PA.
4.
New press on PUSH knob (6) to validate. The parameter stops blinking. a)
Go back to point 1 to
validate
to
and
5.
If no key is pressed, the unit
TX
mode
the display.
I n: the
modulation of the microphone
speaker connected to jack PA.SP. (D). The
the internal loudspeaker [or external optional loudspeaker connected to
jack EXT.SP (C)]. "PA" blinks alternately with the modulation mode (AM or
FM).
OF: The reception is no more functional. Only the
phone
is transmitted to the Public Address loudspeaker connected to jack
PA.SP. (D). PA and le level of the
modulation of the microphone
PA: the
ted to the Public Address loudspeaker connected to jack PA.SP. (D). "PA"
blinks alternately with the modulation mode (AM or FM).
Turn the MIC GAIN knob (4) to
Default PA setting is I n.
See § PA (Public Address) page 24.
11) BAND NAME
This function allows you to
1.
Press the BAND KEY (9) to
2.
Press the PUSH knob (6) for 3 seconds to
3.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
select
to
the BD NAME function.
4.
Press PUSH knob (6) to
5.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
the character of the first digit.
6.
New press on PUSH knob (6) to
on display.
7.
Turn the rotary PUSH knob (6) or use the UP/DN buttons (18) on the micro-
select
phone to
8.
Pressing the PUSH knob (6) again
selected band in point 1. The second digit stops flashing. a) Go back to
point 3 to
adjust
and
exit
MENU.
9.
If no key is pressed, the unit
the display.
27
adjust
another function or b) Press the PTT switch (17)
exit
MENU.
disappears.
exits
MENU after 10 seconds,
is transmitted to the external loud-
received signal
modulation of the micro-
PA
are displayed.
received signal
and the
adjust
the audio level of the mode PA.
rename
bands with two digits.
select
the band to be changed.
enter
MENU.
validate.
The first digit blinks on display.
validate
the first digit. The second digit blinks
the character of the second digit.
confirms
the new name assigned to the
another function or b) Press the PTT switch (17) to
disappears.
exits
MENU after 10 seconds,
disappears on
is transmitted to
are transmit-
is displayed.
validate
disappears on
Publicidad
Tabla de contenido
