Lap-Shoulder Belt Installation - Britax Pavilion 70-G3 Guia Del Usuario

Rear-Facing Installation

Lap-Shoulder Belt Installation

Before You Begin:
• Check that your vehicle belt is compatible for use with child
seats. See pages 6 – 8 for more information.
* If your vehicle seat belt system includes a locking feature,
use of the lock-offs is not required as long as the vehicle seat
belt system is locked. Check your vehicle owner's manual to
determine how to lock your vehicle seat belt system when
installing a child restraint.
• Recline this child seat to position 3 and place rear-facing on the
vehicle seat (see page 15).
* When properly installed in the rear-facing
position, the back angle of the child seat
should be at least 30˚ for children and up
to 45˚ from vertical for infants unable to
maintain head and neck control (not to
exceed 45˚) when the car is parked on a
level surface. Use the blue line as a guide
to achieve the proper recline angle for rear-
facing installations. The blue line will be
parallel to the ground when the child seat angle is at the center
of the angle range (30 – 45˚). If necessary, the proper recline
angle can be achieved by placing a rolled towel or pool noodle
in the vehicle seat bight.
• Britax recommends that the Versa-Tether is used at all times.
Using the tether will improve the stability of the child seat and
reduce the risk of injury. Check your vehicle owner's manual for
tether anchor locations. See page 18 for possible rear-facing
tether configurations.
Install with the lap-shoulder belt as shown above.
IMPORTANT:
• The vehicle seat belt must pass in front of the harness
buckle strap.
• The buckle should be in the inner slot for rear-facing
installation.
22
Loosen the harness.
1
a Lift harness adjuster lever
b Grasp the chest clip and pull outward
* Connect the chest clip for easier
adjustment
Remove the body pillow and
2
unbuckle the harness.
Pull the head restraint cover up,
3
then pull the seat cover forward to
access the rear-facing belt path.
Open the blue lock-off closest
4
to where the vehicle belt will be
buckled.
a Open the locking tab
b Open the clamp
Route the vehicle belt through the
5
rear-facing belt slots, ensuring that
the vehicle belt is routed UNDER
the harness buckle strap, then
buckle. Ensure the vehicle belt is
not twisted.
Push down into the middle of the
6
child seating area with moderate
force while removing all slack
from the bottom (lap) part of the
vehicle belt and close the lock-off.
a Close the clamp over the vehicle belt
b Slide your palm or thumb along the
locking tab until a click is heard (see
page 14)
IMPORTANT: Both the vehicle lap and
shoulder belts must be routed through the
lock-off.
Push down into the middle
7
of the child seating area with
moderate force while pulling
the top (shoulder) part of the belt
between the belt slots to remove
any remaining slack through the
lock-off.
Rear-facing installations can be
8
improved by the use of the Versa-
Tether (see pages 17 – 19).
Pull the buckle up through its
9
appropriate slot in the cover.
Replace the cover.
10
Checklist
9 Check that the vehicle belt is securely fastened.
9 Check that the child seat cannot be moved front to back or side to side
more than 1 in. (2.5 cm) at the belt path. If the child seat is not secure,
repeat installation or use a different seating location.
9 Check that the back angle of the child seat is 30º – 45º from vertical (not
to exceed 45º) when the car is parked on a level surface.
* If necessary, the proper recline angle can be achieved by
placing a rolled towel or pool noodle in the vehicle seat bight.
Rear-Facing Installation
1 b
1 a
4b
4a
LOCKING
TAB
CLAMP
5
5
7
23