Before Starting Engine - Sears Craftsman 247.88755 Manual De Uso

Augers
When engaged, the augers rotate and draw snow into the auger
housing.
Chute Assembly
Snow drawn into the auger housing is discharged out the chute
assembly.
Choke Control
Activating choke control by turning it all the way
to the left closes the choke plate on carburetor
and aids in starting the engine. For information on
choke usage, see Starting The Engine later in this
section.
Recoil Starter & Starter Handle
This motor is fitted with a recoil action pull start and a mitten grip
handle for easy access while wearing gloves or mittens.
Ignition key
The ignition key is a safety device. It must be fully
inserted in order for the engine to start. Remove
the ignition key when the snow thrower is not in
use.
NOTE: Do not turn the ignition key in an attempt to
start the engine. Doing so may cause it to break.
Electric Starter button
Pressing the electric starter button engages the engine's electric
starter when plugged into a 120V power source.
Electric Starter outlet
Requires the use of a three-prong outdoor extension cord (included)
and a 120V power source/wall outlet.
Primer
Depressing primer forces fuel directly into engine's
carburetor to aid in cold-weather starting. Refer to
the starting instructions in the Operation section
of this manual for proper primer usage. The image
below left, corresponds with the label on the
engine identifying the primer.
oil Fill
Remove oil cap to add oil. Refer to the Maintenance & Service section
for checking and adding oil instructions.
gasoline Cap
Remove gas cap to add fuel. Unit runs on regular gas.
NOTE: This unit may include a fuel plug, which is only used during
assembly to keep dirt and debris out of fuel tank. Discard the fuel plug
before filling the fuel tank.
Throttle Control
Operation
The throttle control is located on the engine. It regulates the speed of
the engine and will shut off the engine when pushed down completely.
The image to the right represents the speeds of the throttle control and
corresponds with the label on the engine. The images below illustrate
the definition of each symbol.
Clean-out Tool
Never use your hands to clear a clogged chute assembly. Shut off
engine and remain behind handles until all moving parts have stopped
before using the clean-out tool to clear the chute assembly.
The chute clean-out tool is conveniently fastened to the rear of the
auger housing with a mounting clip. Should snow and ice become
lodged in the chute assembly during operation, proceed as follows to
safely clean the chute assembly and chute opening:
1. Release both the Auger Control and the Drive Control.
2. Stop the engine by removing the ignition key.
3. Remove the clean-out tool from the clip which secures it to the
rear of the auger housing.
4. Use the shovel-shaped end of the clean-out tool to dislodge and
scoop any snow and ice which has formed in and near the chute
assembly.
5. Refasten the clean-out tool to the mounting clip on the rear of
the auger housing, reinsert the ignition key and start the snow
thrower's engine.
6. While standing in the operator's position (behind the snow
thrower), engage the auger control for a few seconds to clear any
remaining snow and ice from the chute assembly.

before Starting Engine

Read, understand, and follow all instructions and warnings on the
machine and in this manual before operating.
Engine oil
The unit was shipped with oil in the engine. Check oil level before each
operation to ensure adequate oil in the engine. For further instructions,
refer to the Maintenance & Service section of this manual.
NOTE: Be sure to check the engine on a level surface with the engine
stopped.
1. Remove the oil filler cap/dipstick and wipe the dipstick clean.
2. Insert the cap/dipstick into the oil filler neck, but do
3. Remove the oil filler cap/dipstick. If the level is low, slowly add
oil (5W-30, with a minimum classification of SF/SG) until oil level
registers between high (H) and low (L).
NOTE: Do not overfill. Overfilling with oil may result in engine smoking,
hard starting or spark plug fouling.
4. Replace and tighten cap/dipstick firmly before starting engine.
13
WARNINg
WARNINg
screw it in.
not