Quick Start - Multiplex FUNCOPTER 21 3001 Instrucciones De Montaje

QUICK START

Be sure to read the Safety Notes before operating the model for the first time.
Depending on the version of the FunCopter you have purchased, you may have to install the electronic components.
MULTIPLEX radio control components for the FunCopter:
AK = Assembled Kit
For the AK version:
Tiny S servo
or Tiny MG servo
MULTIgyro 300DP gyro
MULTIcont BL-37/II speed controller
For the AK and RR versions:
RX-6-SYNTH light receiver
alternatively
or RX-7-DR light M-Link receiver
(only in conjunction with a Multiplex 2.4 GHz transmitter)
Recommended flight battery: Li-BATT FX 3/1-3200
Battery charger:
MULTIcharger LN-3008 EQU
for 2S and 3S LiPo, LiIo and LiFe batteries, also
NiMH and NiCd batteries with four to eight cells
Tools:
Allen keys: 1.5 / 2 / 2.5 / 3 / 4 mm A/F (supplied in the set)
Side-cutters, cross-point screwdriver, slot-head screwdriver (for gyro adjustment), ball-link pliers (recommended).
Please refer to the illustration 'AS' when installing the electronics. The assembly instructions include a detailed illustration of
the servo installation.
The gyro must be installed with the correct orientation (the right way round); for more information please read the instructions
supplied with the unit. The gyro should be mounted on double-sided foam tape, as this absorbs vibration.
The receiver, speed controller and battery should be attached using Velcro (hook-and-loop) tape. It is important to deploy all
cables in such a way that they cannot foul or become tangled in any moving parts.
It is important to consider the centre of gravity (see Fig. 'CG') when installing the flight battery: for hovering the centre of gravity
should be directly below the rotor hub. For higher-speed circuits it is advantageous to position the battery (C.G.) further forward.
The standard pushrods which are installed in the rotor head have proved excellent in practice. For even more accurate fine-
tuning you can use the variable pushrods which are also supplied in the kit: these make it possible to adjust blade tracking (i.e.
set both rotor planes rotating in the same horizontal plane), and thereby minimise vibration caused by imperfect tracking.
Remove the mixer arm pushrods 35 and the snap-fit ball-links 55, and replace them with the variable pushrods (adjustment
links) 13 and screw-fitting ball-links 14: these parts are installed as shown in Figs. MR-05 and MR-06 in the illustrated instructions.
Adjust the pushrod lengths to ensure that there is no stress in the system when the pushrods are installed. Blade tracking can
now be corrected by unscrewing the pushrod on one side, and screwing the pushrod in on the other side by the same number
of turns. This action tilts the rotor yoke, which in turn affects the blade tracking. If you find that blade tracking is worse after
making an alteration, adjust the pushrods again to tilt the rotor yoke in the opposite direction.
26
GB
- RR = Ready for Radio
3 x required (roll, pitch-axis, yaw)
3 x required (roll, pitch-axis, yaw)
35 MHz A/B band
40 / 41 MHz
2.4 GHz
Li-BATT BX 3/1-3200
Li-BATT eco 3/1-3000
Order No. 6 5121
Order No. 6 5122
Order No. 7 5503
Order No. 7 2276
Order No. 5 5876
Order No. 5 5877
Order No. 5 5810
Order No. 15 7371
Order No. 15 7136
Order No. 15 7236
Order No. 9 2540