Sawing With Special Base Runners; Sawing With The Angle Table; Sawing With The Base Adapter; Environment - Festool CARVEX PS 420 EBQ Manual De Instrucciones

cations that are specially designed for your
Festool jigsaw.

10.2 Sawing with special base runners

The special base runners protect high-quality
surfaces against scratches and scores.
► Press in the base runner at position [6-1].
► At the same time, push the base runner for­
wards.
► Mount another base runner and push it to
the rear until it engages.

10.3 Sawing with the angle table

The WT-PS 400 angle table is used for
cutting pipes or interior and exterior an­
gles up to 45°.
Dust extraction is not possible when sawing
with the angle table!
Installing the angle table
► Remove the saw table [1-12] (see section
7.4 ).
► Position the angle table against the saw
base support.
► Close the lever [1-10].
Ensure that the angle table is firmly seated in
the guide.
Setting the angle
► Turn the adjusting wheel [7-1] to select the
required angle.
You can select the angles -45°, 0° and +45° on
the scale [7-2].
WARNING
Sawing cutting depths
Risk of injury
► Select the saw blade length and cutting
depth so that the saw blade remains
plunged in the workpiece.
For 0° cuts, we recommend setting the an­
gle table to a small negative angle to guar­
antee smooth operation.

10.4 Sawing with the base adapter

The ADT-PS 400 base adapter is used for at­
taching your jigsaw to the Festool guide rail and
the KS-PS 400 core maker.
With guide rail and core maker: Observe
the max. material thickness of 20 mm
and only use cross-set saw blades (FSG).
Installing the base adapter
► Remove the saw table [1-12] (see section
7.4 ).
► Position the base adapter [8-1] against the
saw table support.
► Close the lever [1-10].
Ensure that the base adapter is firmly seated in
the guide.
Also use the extractor connector [1-9]
with the base adapter.
Adaptation to the FS 2 guide rail
The FS 2 Festool guide system (Fig. [9]) makes
it much easier to produce straight and precise
cuts.
► Place the jigsaw with attached base adapter
[8-1] on the guide rail.
Adaptation to the core maker
The core maker can be used to create circular
cuts with a diameter between 120 and
3000 mm. The core maker can be installed from
both sides on the base adapter.
► Place the jigsaw with attached base adapter
on the adapter [10-1] on the core maker.
► Insert the centring mandrel [10-2] in the
hole [10-4] on the core maker aligned with
the saw blade.
► Clamp the measuring tape to the core mak­
er using the rotary knob [10-5].
Recommended settings when using the core
maker:
► Cut in an anticlockwise direction.
► Work at a slow rate of advance.
► Set the pendulum stroke [1-13] to 0–1.
► Set the stroke rate [1-6] to 1–5.
Store the centring mandrel in the depot
[10-3].
Semi-stationary sawing with the Festool CMS
system
When combined with the Festool CMS system,
the jigsaw becomes a semi-stationary bench
saw for profiled cuts. See the CMS brochure for
more information.
► Install your jigsaw with base adapter in the
CMS as described in the operating manual
for the CMS-PS.

11 Environment

Do not dispose of the device in the
household waste! Recycle devices, ac­
cessories and packaging. Observe appli­
cable national regulations.
EU only: In accordance with the European Di­
rective on waste electrical and electronic
equipment and implementation in national law,
English
21