Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Auxiliary function
Low temperature
This function allows for drying at lower
temperatures and therefore saves energy.
Warning LED will light up when you select the
function.
C
You must use this function when you dry
your synthetic or delicate laundry.
Warning indicators
C
Warning indicators may differ according to
the model of your machine.
Filter cleaning
A warning LED will light up to remind filter
cleaning after the program finishes.
C
If the filter cleaning warning LED lights
up continuously, please refer to, "Solution
suggestions for problems".
Water tank
A
warning LED will light up at the end of the
program or when the tank is full with water.
The machine stops operating when this
warning LED lights up during a program
running. To restart the machine, please
drain the water in the water tank. Press
"Start/Pause/Cancel" button to start the
program after you have emptied the water
tank. The warning LED goes off and the
program resumes operating.
Starting the Program
1. Press "Start/Pause/Cancel" button to start
the program.
2. "Start/Pause/Cancel" button will light up to
indicate that the program has started.
Timer follow-up indicator
One of the lamps is on as far as program runs
and shows the approximate remaining time.
C
LEDs on the timer follow-up indicator
will also flash when the child-proof lock is
activated.
A
If more than one LED light up or
flash concurrently, it means there is
malfunctioning or a failure (please see,
Solution suggestions for problems).
Changing the program after the program
has started
You can use this feature to dry your laundry
in a different program after your machine has
started to run.
For example;
Press and hold the "Start/Pause/Cancel"
button for about 3 seconds to select "80"
minutes program instead of "60" minutes
program.
Select the "80" minutes program by rotating
the program knob.
Press "Start/Pause/Cancel" button to start the
program.
C
The program which is selected first will
go on even if the program selection button
is moved and another program mode is
selected while the machine is operating.
You must cancel the ongoing program in
order to change the drying program. (See,
Ending the program through canceling)
Adding/removing laundry in standby
mode
In order to add or take out laundry after the
start-up of the program;
1. Press the "Start/Pause/Cancel" button
to switch the machine to "Pause" mode.
Drying process will stop.
2. Open the door at Pause position and close
it again after adding or taking out laundry.
3. Press "Start/Pause/Cancel" button to start
the program.
C
Any laundry added after the drying
process was started may cause the already
dried clothes in the machine intermingle
with wet clothes and the result will be wet
laundry after the drying process is over.
C
Laundry may be added or taken out as
much as desired during a drying process,
but as this process will interrupt drying
continuously, it will extend the program
duration and increase energy consumption.
Therefore, it is recommended to add
laundry before the drying program is
started.
Child-proof lock
There is a childproof lock to prevent any
program interruption due to the pressing of
keys while the program is on. The loading
door and all keys except the "On/Off" key on
the panel are deactivated when the child-proof
lock is active.
In order to activate the childproof lock, press
on the "Start/Pause/Cancel" and "Low
temperature" buttons simultaneously for 3
seconds.
To start a new program after the program is
over or to interrupt the program, the childproof
lock should be deactivated. To deactivate the
childproof lock, press the same buttons for 3
sec.
C
One of the LEDs on the program follow-up
indicator starts flashing when the child-
proof lock is activated.
C
Child-proof lock is deactivated when the
machine is restarted by pressing the On/Off
button.
13 - EN
Publicidad
Tabla de contenido
