Mitsubishi Electric PUZ-A18-NHA6 Para El Instalador página 10

 7HVW UXQ
7KH IROORZLQJV PXVW EH FKHFNHG DV ZHOO
‡ 7KH RXWGRRU XQLW LV QRW IDXOW\ /(' DQG /(' RQ WKH FRQWURO ERDUG RI WKH RXWGRRU
XQLW ÀDVK ZKHQ WKH RXWGRRU XQLW LV IDXOW\
‡ %RWK WKH JDV DQG OLTXLG VWRS YDOYHV DUH FRPSOHWHO\ RSHQ
‡ A protective sheet covers the surface of the DIP switch panel on the control board
of the outdoor unit. Remove the protective sheet to operate the DIP switches easily.
 7HVW UXQ
 8VLQJ 6: LQ RXWGRRU XQLW
1) PUZ Type
SW4-1 ON
Cooling operation
SW4-2 OFF
SW4-1 ON
Heating operation
SW4-2 ON
 38< 7\SH
SW4-1 ON
Cooling operation
SW4-2 ON or OFF
* After performing the test run, set SW4-1 to OFF.
‡ $IWHU SRZHU LV VXSSOLHG D VPDOO FOLFNLQJ QRLVH PD\ EH KHDUG IURP WKH LQVLGH RI WKH
outdoor unit. The electronic expansion valve is opening and closing. The unit is
not faulty.
 6SHFLDO )XQFWLRQV
A
B
SW1
E
A Circuit diagram example (low noise mode)
B On-site arrangement
C External input adapter (PAC-SC36NA-E)
A
B
SW2
E
A Circuit diagram example
(Demand function)
B On-site arrangement
 5HIULJHUDQW FROOHFWLQJ SXPS GRZQ
Perform the following procedures to collect the refrigerant when moving the indoor
unit or the outdoor unit.
1 Supply power (circuit breaker).
* When power is supplied, make sure that "CENTRALLY CONTROLLED" is not
displayed on the remote controller. If "CENTRALLY CONTROLLED" is dis-
played, the refrigerant collecting (pump down) cannot be completed normally.
* Start-up of the indoor-outdoor communication takes about 3 minutes after the
power (circuit breaker) is turned on. Start the pump-down operation 3 to 4 min-
utes after the power (circuit breaker) is turned ON.
2 After the liquid stop valve is closed, set the SWP switch on the control board of the
outdoor unit to ON. The compressor (outdoor unit) and fans (indoor and outdoor
units) start operating and refrigerant collecting operation begins. LED1 and LED2
on the control board of the outdoor unit are lit.
* Only set the SWP switch (push-button type) to ON if the unit is stopped. How-
ever, even if the unit is stopped and the SWP switch is set to ON less than 3
minutes after the compressor stops, the refrigerant collecting operation cannot
be performed. Wait until compressor has been stopped for 3 minutes and then
set the SWP switch to ON again.
10
C D
Red
3 3
Brown
Orange
1 1 )LJ 
CNDM
D Outdoor unit control board
E Max. 10 m, 33 ft
C D
Red
3 3
Brown
)LJ 
Orange 1 1
CNDM
C External input adapter
(PAC-SC36NA-E)
D Outdoor unit control board
E Max. 10 m, 33 ft
‡ 0DNH VXUH WKDW WKH DOO RI WKH 6: ',3 VZLWFKHV IRU IXQFWLRQ FKDQJHV RQ WKH FRQWURO
board of the outdoor unit are set to OFF. If all of the SW5 switches are not set to
OFF, record the settings and then set all of the switches to OFF. Begin recovering
the refrigerant. After moving the unit to a new location and completing the test run,
set the SW5 switches to the previously recorded settings.
‡ $ IHZ VHFRQGV DIWHU WKH FRPSUHVVRU VWDUWV D FODQJLQJ QRLVH PD\ EH KHDUG IURP
the inside of the outdoor unit. The noise is coming from the check valve due to the
small difference in pressure in the pipes. The unit is not faulty.
7KH WHVW UXQ RSHUDWLRQ PRGH FDQQRW EH FKDQJHG E\ ',3 VZLWFK 6: GXULQJ
the test run. (To change the test run operation mode during the test run, stop
WKH WHVW UXQ E\ ',3 VZLWFK 6: $IWHU FKDQJLQJ WKH WHVW UXQ RSHUDWLRQ PRGH
UHVXPH WKH WHVW UXQ E\ VZLWFK 6:
 8VLQJ UHPRWH FRQWUROOHU
Refer to the indoor unit installation manual.
 /RZ QRLVH PRGH RQVLWH PRGL¿FDWLRQ )LJ 
%\ SHUIRUPLQJ WKH IROORZLQJ PRGL¿FDWLRQ RSHUDWLRQ QRLVH RI WKH RXWGRRU XQLW FDQ EH
reduced by about 3-4 dB.
The low noise mode will be activated when a commercially available timer or the
contact input of an ON/OFF switch is added to the CNDM connector (option) on the
control board of the outdoor unit.
‡ 7KH FDSDFLW\ PD\ EH LQVXI¿FLHQW DFFRUGLQJ WR WKH RXWGRRU WHPSHUDWXUH DQG FRQGL-
tions, etc.
1 Complete the circuit as shown when using the external input adapter (PAC-SC-
36NA-E). (Option)
2 SW1 ON: Low noise mode
SW1 OFF: Normal operation
 'HPDQG IXQFWLRQ RQVLWH PRGL¿FDWLRQ )LJ 
%\ SHUIRUPLQJ WKH IROORZLQJ PRGL¿FDWLRQ HQHUJ\ FRQVXPSWLRQ FDQ EH UHGXFHG WR 
–100% of the normal consumption.
The demand function will be activated when a commercially available timer or the
contact input of an ON/OFF switch is added to the CNDM connector (option) on the
control board of the outdoor unit.
1 Complete the circuit as shown when using the external input adapter
(PAC-SC36NA-E). (Option)
2 By setting SW7-1 and SW7-2 on the control board of the outdoor unit, the energy
consumption (compared to the normal consumption) can be limited as shown
below.
SW7-1 SW7-2
OFF OFF
ON OFF
OFF ON
3 Because the unit automatically stops in about 2 to 3 minutes when the refrigerant
collecting operation is completed (LED1 off, LED2 lit), be sure to quickly close
the gas stop valve. If LED1 is lit and LED 2 is off and the outdoor unit is stopped,
refrigerant collection is not properly performed. Open the liquid stop valve com-
pletely, and then repeat step 2 after 3 minutes have passed.
* If the refrigerant collecting operation has been completed normally (LED1 off,
LED2 lit), the unit will remain stopped until the power supply is turned off.
4 Turn off the power supply (circuit breaker).
* Note that when the extension piping is very long with large refrigerant amount,
it may not be possible to perform a pump-down operation. When performing the
pump-down operation, make sure that the low pressure is lowered to near 0
MPa (gauge).
Warning:
When pumping down the refrigerant, stop the compressor before disconnect-
ing the refrigerant pipes. The compressor may burst if air etc. get into it.
Energy consumption (SW2 ON)
0% (Stop)
50%
75%