Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Preparatory work
Getting to know the appliance
Fig.
:
Dust bin cover release;
1
1
hose release;
dust bin cover;
3
4
dle;
dust bin release;
6
parking bracket;
exhaust filter cover;
8
9
nection cord;
ON/OFF button;
11
with accessory bracket;
telescopic tube;
suction hose port;
15
16
scopic tube release catch;
carpet nozzle;
3-in-1 combi nozzle
19
20
Accessories (optional):
parquet nozzle;
mini turbo nozzle
A
B
Unpacking and assembling
Check that the unpackaged contents are com-
1
plete. If you notice any transport damage or if an-
ything is missing, contact your dealer immediate-
ly.
Connect suction hose and appliance (Fig.
2
Connect the suction hose with the telescopic tube
3
and adjust the length of the telescopic tube (Fig.
Connect telescopic tube and switchable floor noz-
4
zle (Fig.
).
Ensure that the bypass vent (Fig.
4
5
is completely closed.
Using the accessories
CAUTION!
For hard floors, only use the switchable floor
nozzle (Fig.
/
) with the brush (Fig.
1
19
tended, as the hard floor may otherwise become
damaged.
CAUTION!
If using the turbo nozzle (Fig.
that the surface can withstand the rotating brush
without becoming damaged.
NOTE:
The carpet nozzle (fig.
oped specially for carpets and cleans deep down.
As a result of its design it may adhere firmly to the
carpet. This adhesion can be reduced using the
bypass vent (fig.
/
1
14
Do not use the carpet nozzle for hard floors as
the hard floors will otherwise become damaged.
NOTE:
You can also use the suction nozzles without the
telescopic tube as necessary. To do so, connect
the required accessories directly to the handle
(Fig.
).
9
dust bin;
2
dust bin han-
5
cord rewind button;
7
con-
10
suction hose
12
handle;
bypass vent;
13,
14
tele-
17
switchable floor nozzle;
18
1
) ex-
10
1
/B), make sure
/
) is a nozzle devel-
1
19
).
EN
Connect the required accessory to the handle or
1
the telescopic tube (Fig.
accessory is securely connected. ➔ The appliance
can be connected.
Connecting the appliance
CAUTION!
If the red marking is visible (Fig.
the connection cord by pressing the cord rewind
button to pull in the cord up to the yellow mark
(Fig.
/
) (Fig.
6
2
cord might be damaged.
Pull the cable out of the appliance (Fig.
1
sert the plug into a mains socket.
Vacuum cleaning
Flexible vacuum-cleaning
).
2
Connect the required accessories >"Using the ac-
1
).
3
cessories" on page 17.
>"Connecting the appliance" on page 17.
/
)
on the appliance, press the ON/OFF button (Fig.
15
➔ The appliance vacuums at full suction power.
Set the desired suction power on the power con-
4
troller (fig.
11
) and vacuum-clean.
the appliance, press the ON/OFF button again
). ➔ The appliance switches off.
(Fig.
8
bypass vent (Fig.
ates with full suction power when vacuum-cleaning
the next time.
Regulating the suction power
To reduce the suction power, turn the power con-
1
troller down (fig.
er, turn the power controller up (fig.
Storing the appliance
NOTE:
If necessary, use the holding clip on the suction
hose (fig.
/
1
Switch off the appliance and pull the plug from the
1
socket.
Push the cord rewind button (Fig.
2
until the cord has been fully rewound (Fig.
Hang the telescopic floor nozzle or parquet nozzle
3
(connected to the telescopic tube or handle) in the
parking bracket (Fig.
).
Make sure that the
9
2
/
6
1
). Otherwise, the connection
7
Connect the appliance
2
To switch off
5
/
) so that the appliance oper-
1
15
).
To increase the suction pow-
11
2
).
11
) to attach accessories.
13
1
/
) (Fig.
12
).
8
17
), retract
).
In-
5
2
To switch
3
).
8
4
Close the
6
1
/
)
6
).
7
Publicidad
Tabla de contenido
