Know Your Product; Operation - SPARKY HeavyDuty BR2 10.8Li HD Instrucciones De Uso

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 41
During the charging process the charger and battery
might become warm. This is a normal condition, and
does not indicate a problem.
▪ After completion of charging which takes approxi-
mately 30 min, the red LED ceases to glow and the
green LED lights up.
The charger features thermal overload protection for the
battery. Nevertheless we recommend withdrawing the
battery from the charger upon expiring of the charging
time. You may use additionally an electric timer in order
to control the charging time.
TO OBTAIN THE BEST LIFE FOR THE BATTERY
▪ When battery is not in use, keep it away from other
metal objects like paper clips, coins, keys, nails,
screws, or other small metal objects that can make
a connection from one terminal to another. Shorting
the battery terminals together may cause fire or ex-
plosion.
▪ Always unplug the charger when not in use and store
in a dry secure place.
▪ Do not charge battery packs and do not store the
charger in premises where the temperature may drop
under 0ºC or exceed +40ºC.
BATTERY STATE INDICATION
The battery state during operation can be checked on
the LED display (7) by pressing the indicator button (6).
(Fig. 2)
Depending on the number of illuminated LEDs the bat-
tery state is as follows:
3 = Battery 100% - 60% charged.
2 = Battery 60% - 30% charged.
1 = Battery < 30% charged. It is necessary to recharge
the battery.
The direction of decreasing the charge level indicated by
the LEDs is marked on the housing of the power tool.
VII - Know your product
Before using the power tool, familiarize yourself with all
operating features and safety requirements.
Use the tool and accessories only for the applications
intended. All other applications are expressly ruled out.
1. Keyless chuck
2. Speed selector switch
3. Forward/reverse switch
4. Battery release buttons
5. Battery
6. ON/OFF trigger switch
7. Battery state indicator
8. LED light
9. Torque adjustment collar
10. Charger
11. LED charge state indicator
Original instructions
pages BR2-10.8LiHD-2012.indd 7
VIII - Operation
LED WORK AREA LIGHT
The machine is equipped with LED light (8) to illuminate
the work area and improve visibility when drilling in areas
with insufficient light. To turn the LED light on and off de-
press the LED light button (6).
REVERSING
The extreme position of lever (3) to the right (viewed from
the rear) is equivalent to anti-clockwise rotation, the ex-
treme position to the left - to clockwise rotation. When
the ON/OFF switch (6) is depressed lever (3) can not be
actuated. (Fig. 3)
WARNING: Reversing can be performed only
when the spindle is not rotating!
Drilling and tightening screws are performed with lever
in extreme position to the left. Removal of screws is per-
formed with lever in extreme position to the right.
SWITCHING ON - SWITCHING OFF
Switching on: press ON/OFF switch (6).
Switching off: release ON/OFF switch (6).
The power tool is equipped with a brake. The spindle
stops rotating immediately after releasing the switch le-
ver.
SMOOTH ELECTRONIC RPM CONTROL
Light pressure on ON/OFF trigger switch (6) results in
low rotation speed, further pressing the switch results in
smooth increase of the rpm to maximum upon reaching
the extreme position.
ADJUSTING THE TORQUE
Rotate the torque adjustment collar (9) behind the chuck,
to adjust the torque to each of 17 settings.
The range of 17 torque settings allows better control
when using the drill as a screwdriver thus preventing
over-tightening of the screws.
The numbers circling the collar are used to indicate the
level of torque. The larger the number on the collar, the
higher the torque. To select any of the numbers, rotate
the collar (9) until the desired number aligns with the ar-
row head indicator on the housing of the machine.
Screwdriving
Set the torque adjustment collar (9) against one
of 17 positions.
Select low setting range for working with small
screws or in soft materials.
Select high setting range for working with large
screws or in hard materials.
7
EN
26.9.2012 . 13:25:31 .

Publicidad

Tabla de contenido
loading

Tabla de contenido