Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
4. INSTALLING THE CHILD SEAT REARWARD FACING
GROUP 0+
(3 POINTS BELT ONLY)
GROUP 0+ only. From birth to 12 months
NOTICE
approx. (0-13 kg)
1. Before installing the child seat, the position of the seat must be
adjust to rearward facing. To do it, pull and keep up the lock system
of the seat base
(S)
(fig.3.1). Rotate the seat to rearward facing (fig.3.2).
2. Place the child safety seat in the back seat of the vehicle facing in
the opposite direction of travel ensuring it is resting firmly against
the backrest.
3. Unlock the harness to help seat installation.
4. Take out the reducer cushion
5. Pass the abdominal strap of the seat belt through the lower seat
guides
(J)
(fig. 4.1) and buckle the vehicle seat belt until you hear a
click (fig.4.2).
6. Pass the diagonal section of the seat belt through the
corresponding upper guide (L).
7. Take the remaining slack of the diagonal section of the 3-point
seat belt. And make sure it is as tight fitting as possible.
8. Ensure the straps are not twisted or knotted at any point.
9. Place back the reductor cushion
5. INSTALLING THE CHILD SEAT FORWARD FACING
GROUP 1
(ISOFIX+TOP TETHER)
GROUP 1 only. From 9 months to 4 years
NOTICE
approx. (9-18 kg)
WARNING! once the car seat is installed, if another recline position
is selected, you should check the tension of the Top Tether system.
1. Before installing the child seat, select 1, 2, 3 or 4 recline positions
(fig. 5.1). Pull the lever
(I)
without releasing the lever until the seat is in the desired position.
30
(K)
from the seat.
(K)
on the seat.
forward and adjust the angle of recline
2. Press the ISOFIX adjuster button
and pull them outward (fig. 5.2). Move each locking arm to check
that it is completely deployed.
3. Take the Top Tether
(P)
and pass it over the seat.
4. Place the child safety seat in the back seat of the vehicle facing in
the direction of travel.
5. Hold the safety seat with both hands and insert the two locking
arms
(N)
into the vehicle´s Isofix connectors until they fasten with
a click on both sides. The red button will change to green on both
sides (fig. 5.3).
6. Shake the seat to check that it is correctly anchored to the vehicle's
ISOFIX points.
IMPORTANT! The locking arms are only correctly fixed if both safety
buttons are green.
7. Push the safety seat towards the back using a firm, constant
pressure on both sides until it rests firmly against the vehicle seat
(fig. 5.4). If necessary, adjust the reclining of the vehicle´s seat
backrest to ensure that the child seat rests correctly.
8. Take the Top Tether and press the Top Tether
the strap.
9. Hook the safety clasp to the Top Tether anchor point recommended
in your vehicle instruction manual (fig. 5.5)
IMPORTANT! Make sure not to use the luggage clip instead
of the Top Tether anchor clip. Look for this symbol in your
vehicle.
10. To tighten the Top Tether, take up any slack by pulling the free end of
the belt through the Top Tether adjuster (fig. 5.6). The Top Tether will
be correctly tightened when tension indicator turns from red to green
(fig. 5.7).
Uninstalling the ISOFIX arms
To release the ISOFIX arms, pull the button on the anchors
unlock them until the indicator turns from green to red color. This
will release the child seat (fig. 5.8).
(M)
to unlock the Isofix arms
(N)
(P)
adjuster to stretch
(M)
to
31
Publicidad
Tabla de contenido
