Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
6. INSTALLING THE CHILD SEAT FORWARD FACING
GROUP 1
(3 POINTS BELT ONLY)
GROUP 1 only. From 4 years to 12 years
NOTICE
approx. (15-36 kg)
WARNING! once the car seat is installed, if another recline
position is selected, you should repeat the car seat installation
steps described below to ensure a proper installation is in this new
position.
1. Before installing the child seat, select 1, 2, 3 or 4 recline position
(fig. 6.1). Pull the lever
(I)
forward and adjust the angle of recline
without releasing the lever until the seat is in the desired position.
2. Place the child safety seat in the back seat of the vehicle facing
in the direction of travel ensuring it is resting firmly against the
backrest.
3. Unlock the harness to help seat installation.
4. Take out the reducer cushion
5. Pass the diagonal section of the vehicle belt over the red guide
(L), which is located behind the headrest. Pass the abdominal
section of the belt through the guides
6. Insert the security belt on the vehicle anchor point and press until
hear a "click" that indicates the child seat is correctly installed.
7. To tighten the belt, using the knee press down the child seat while
take up any slack by pulling the belt(fig. 6.4).
8. Make sure the vehicle belt in not twisted.
9. Place back the reductor cushion
7. FASTENING THE CHILD SEAT GROUP 0+/1
Proper adjustment of the height of the headrest ensures the child
will be seated correctly. The headrest should be adjusted to ensure
that the harness straps
(E)
should be adjusted to the height of the
child's shoulder or slightly above; never behind the child's back or
level with the ears (fig. 7.1).
The headrest and shoulder straps height can be adjusted by this way:
32
(K)
from the seat.
(J)
(fig. 6.2 and 6.3).
(K)
on the seat.
Loosen the security seats´shoulder straps the maximum as possible.
For it:
a. Loosen the harness straps
(E)
by pulling them gently while
pressing the harness adjustment button
b. Adjust the headrest according to the child´s height by pulling the
headrest height regulator
(A)
adjusting the harness to the height
of the child´s shoulder or slightly above (fig. 7.3).
1. Pressing the red button, release the buckle
the child (fig. 7.3).
3. Place the child in the seat.
4. Secure the child with the harness by joining the two
parts of the clasp and fasten the buckle until you hear a
click (fig. 7.4 and 7.5).
5. Gently pull the harness adjustment strap
correct tension (fig. 7.8). Remember that in order to ensure the
child's safety the harnesses should fit tightly.
8. INSTALLING THE CHILD SEAT FORWARD FACING
GROUP 2/3
(ISOCLICK FIX
, TOP TETHER AND 3 POINTS BELT)
®
GROUP 2/3 only. From 4 years to 12 years
NOTICE
approx. (15-36 kg)
8.1 Removing the 5 point harness and the safety buckle
Before installing the seat for Group 2/3, the seat harnesses (E),
harness protectors
(D)
and buckle
(E)
1. Loosen the harness straps
by pulling them gently while pressing
the harness adjustment button
(G)
2. Loosen the harness straps from the back of the seat, freeing them
from the harness connector (R). Remove them pulling up from the
front side of the seat.
3. Take out the headrest brake and the shoulder protectors and
store them for future uses(fig.8.2 and 8.3)
4. Lift the cover and by folding the harness straps, store them in a
non disturbing place of the backrest (fig. 8.4)
(G)
(fig. 7.2).
(F)
to help to install
(H)
to achieve the
(F)
must be removed. For it:
(fig. 7.2)
33
Publicidad
Tabla de contenido
