SPARKY HeavyDuty FB 514 Instrucciones De Uso página 8

forces, if proper precautions are taken.
b) Never place your hand near the rotating acces-
sory. Accessory may kickback over your hand.
c) Do not position your body in the area where
power tool will move if kickback occurs. Kick-
back will propel the tool in direction opposite to the
wheel's movement at the point of snagging.
d) Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing
have a tendency to snag the rotating accessory
and cause loss of control or kickback.
e) Do not attach a saw chain woodcarving blade
or toothed saw blade. Such blades create fre-
quent kickback and loss of control.
▪ Fix the machined piece in vice or in another ap-
propriate way.
Safety Warnings Specific for Grinding:
a) Use only wheel types that are recommended
for your power tool and the specific guard de-
signed for the selected wheel. Wheels for which
the power tool was not designed cannot be ade-
quately guarded and are unsafe.
b) The grinding surface of centre depressed
wheels must be mounted below the plane of
the guard lip. An improperly mounted wheel that
projects through the plane of the guard lip cannot
be adequately protected.
c) The guard must be securely attached to the
power tool and positioned for maximum safe-
ty, so the least amount of wheel is exposed to-
wards the operator. The guard helps to protect
the operator from broken wheel fragments, ac-
cidental contact with wheel and sparks that could
ignite clothing.
d) Wheels must be used only for recommended
applications. For example: do not grind with
the side of cut-off wheel. Abrasive cut-off wheels
are intended for peripheral grinding, side forces ap-
plied to these wheels may cause them to shatter.
e) Always use undamaged wheel flanges that
are of correct size and shape for your selected
wheel. Proper wheel flanges support the wheel
thus reducing the possibility of wheel break-
age. Flanges for cut-off wheels may be different
from grinding wheel flanges.
Additional Safety Warnings
WARNING: Before connecting a tool to a power
source be sure that the voltage supply is the same as that
specified on the nameplate of the tool.
▪ A power source with a voltage greater than that speci-
fied for the tool can result in serious injury to the user,
as well as damage to the tool.
▪ If in doubt, do not plug in the tool.
▪ Using a power source with a voltage less than the
nameplate rating is harmful to the motor.
Always wear eye and ear protection
and use a dust mask. The dust and abrasive particles
6
EN
pages-FB-514HD-2017.indd 6
separated during operation may seriously injure your
health.
▪ When operating in dusty environment, the ven-
tilation slots must be kept clean. If it should be-
come necessary to clear dust, first disconnect
the tool from the mains supply (remove the bat-
tery) use non metallic objects to clean the dust
and avoid damaging internal parts. The power tool
will overheat under deteriorated cooling due to the
clogged with dust ventilation slots.
▪ Hold power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or
its own cord. Cutting accessory contacting a "live"
wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
▪ Always switch off and unplug the power tool prior
to any adjustment, servicing or maintenance.
▪ The outer metal parts and the bits may get hot after
continuous operation.
▪ Use clamps or a vice to secure your work whenever
possible.
▪ Always switch off the machine and wait until the spin-
dle has come to a complete standstill before placing
it down.
▪ Do not force the machine: let the tool do the work at a
reasonable speed. Overloading will occur if too much
pressure is applied and the motor slows resulting in
inefficient work and possible damage to the motor.
▪ Rags, cloths, cord, string and the like should never be
left around the work area.
▪ Remove any nails, screws, etc. from the processed
surface.
▪ Before using the tool on an actual work piece, switch
on and let it run for a while. Operate the tool at least
200 mm away from your face and body.
▪ Always be sure you have a firm footing. Be sure no
one is below when using the tool in high locations.
▪ Hold the power tool firmly.
▪ Keep your hands away from rotating parts. Do not
touch the bit or the work piece immediately after op-
eration - they may be extremely hot and you may get
serious burns.
▪ The tool must be used only for its prescribed purpose.
Any use other than those mentioned in this Manual
will be considered a case of misuse. The user and not
the manufacturer shall be liable for any damage or in-
jury resulting from such cases of misuse.
▪ To use this tool properly, you must observe the safety
regulations, the assembly instructions and the operat-
ing instructions found in this Manual. All persons who
use and service the machine have to be acquainted
with this Manual and must be informed about its po-
tential hazards. Children and frail people must not use
this tool. Children should be supervised at all times if
they are in the area in which the tool is being used. It
is also imperative that you observe the accident pre-
vention regulations in force in your area. The same
applies for general rules of occupational health and
safety.
▪ The manufacturer shall not be liable for any changes
made to the tool nor for any damage resulting from
such changes.
FB 514
25.5.2017 . 10:30:56