Safety Rules For Laser Lights; Know Your Product - SPARKY TKN 65 Instrucciones De Uso

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 48
ported at the same height as the saw table top. Sup-
ports should be positioned in such as a way to ensure
that the workpiece does not fall to the ground once
the cut has been made. A number of supports at
regular intervals may be required if the workpiece
is extremely long.
▪ Take additional care when trenching (slotting).
▪ Ensure that the arm is properly secure when bev-
elling.
▪ Always stand to one side when operating the saw.
▪ If you are interrupted when operating the saw,
complete the process and switch off before look-
ing up.
▪ Periodically check that all nuts, bolts and other fixings
are properly tightened.
▪ Avoid cutting nails. Inspect the workpiece and remove
all nails and other foreign objects before beginning
sawing.
▪ Do not use the saw to cut metal or masonry.
▪ Do not use this saw to cut firewood.
▪ The mitre saw can be safely carried by the transporta-
tion handle but only once it has been removed from
the mains power and secured in the locked down
position.
▪ Store the machine in a safe manner when not being
used. The storage location must be dry and lockable.
This prevents the machine from storage damage, and
from being operated by untrained persons.
▪ Fully unwind cable drum extensions to avoid potential
overheating.
▪ Connect the saw to a dust collection device and en-
sure that it is operated properly. As the operator of the
saw, please make sure that you understand factors
that influence exposure to dust, including the type of
material to be machined, the importance of local ex-
traction and the proper adjustment of hoods/baffles/
shoots of your dust extraction system. We recom-
mend that you always wear a dust mask when operat-
ing this saw.
▪ Report faults in the machine, including guards and
saw blades, as soon as they are discovered.
▪ Ensure that the operator is adequately trained in the
use, adjustment and operation of the machine.
▪ To use this tool properly, you must observe the safety
regulations, the assembly instructions and the oper-
ating instructions to be found in this Manual. All per-
sons who use and service the machine have to be
acquainted with this Manual and must be informed
about its potential hazards. Children and frail people
must not use this tool. Children should be supervised
at all times if they are in the area in which the tool is
being used. It is also imperative that you observe the
accident prevention regulations in force in your area.
The same applies for general rules of occupational
health and safety.
▪ The manufacturer shall not be liable for any changes
made to the tool nor for any damage resulting from
such changes.
▪ Power tools must not be used outdoors in rainy weath-
er, or in moist environment (after rain) or in close vicin-
ity with easily flammable liquids and gases. The work-
ing place should be well lit.
6
EN
V - Safety rules for laser
lights
The laser light used in the REDEYE
2 with maximum 1 mW power and 650 nm wavelength.
These lasers do not normally present an optical hazard,
although staring at the beam may cause flash blindness.
WARNING: Do not stare directly at the laser
beam. A hazard may exist if you deliberately stare into
the beam, please observe all safety rules as follows:
Please observe the following safety rules:
▪ The laser shall be used and maintained in accordance
with the manufacturer's instructions.
▪ Never aim the beam at any person or an object other
than the workpiece.
▪ The laser beam shall not be deliberately aimed at
personnel and shall be prevented from being directed
toward the eye of a person for longer than 0.25 s.
▪ Always ensure the laser beam is aimed at a sturdy
workpiece without reflective surfaces. i.e. wood or
rough coated surfaces are acceptable. Bright shiny
reflective sheet steel or the like is not suitable for laser
use as the reflective surface could direct the beam
back at the operator.
▪ Do not change the laser light assembly with a differ-
ent type. Repairs must be carried out by the laser
manu¬facturer or an authorised agent.
WARNING: Use of controls or adjustments or
performance of procedures other than those specified
herein may result in hazardous radiation exposure.
VI - Know your product
1. Work clamp securing knob
2. Work clamp
3. Bevel scale
4. Laser guide
5. Depth stop lever
6. Dust bag
7. Depth adjustment knob
8. Dust extraction port
9. Guard retraction arm
1 0. Fixed blade guard
11. Transportation handle
12. Operating handle
1 3. ON/OFF switch
14. Guard release latch
15. Screw
16. Retractable safety guard
®
system is Class
Max. radiant power ≤ 1mW
Wave length 650 nm
IEC 60825-1:07
LASER BEAM
DO NOT STARE INTO BEAM
CLASS 2 LASER DEVICE
TKN 65

Publicidad

Tabla de contenido
loading

Tabla de contenido