Publicidad
Idiomas disponibles
Idiomas disponibles
REPLACING THE BATTERY
（
only OM1500ATLCD
Replacement of batteries located in an OPERATOR ACCESS AREA.
1. When replacing batteries, replace with the same number of the following battery: Cyberpower /
RBP0089for the OM1500ATLCD.
2. CAUTION! Risk of Energy Hazard, 12V, maximum 7.5Ampere-hour battery. Before replacing
batteries, remove conductive jewelry such as chains, wrist watches, and rings. High energy
conducted through these materials could cause severe burns.
3. CAUTION! Do not dispose of batteries in a fire. The batteries may explode.
4. CAUTION! Do not open or mutilate batteries. Released material is harmful to the skin and eyes.
It may be toxic.
5. CAUTION! A battery can present a risk of electrical shock and high short circuit current. The
following precautions should be observed when working on batteries:
1) Remove watches rings, or other metal objects.
2) Use tools with insulated handles.
CAUTION - RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDING TO LOCAL REGULATIONS.
BATTERY REPLACEMENT PROCEDURE
1.
Turn off and unplug all connected equipment.
2.
Turn the UPS off and unplug it from the AC power source.
3.
Turn the UPS on its side.
4.
Remove the screws on the bottom of the front panel and lay aside.
5.
Remove the front panel of the UPS: pull and lift it.
6.
Take out the battery compartment cover.
7.
Disconnect the battery wires from the battery.
8.
Remove the battery from the compartment.
9.
Put the battery back into the compartment.
10. Install the replacement battery by connecting the red wire (+) and black wire (-) to the same color
connectors from the battery pack.
11. Replace the battery compartment cover.
12. Align the front panel and tighten the retaining screws.
13. Recharge the UPS for 8-16 hours to fully charge the battery.
REMINDER: Batteries are considered HAZARDOUS WASTE and must be disposed of properly.
Most retailers that sell lead-acid batteries collect used batteries for recycling, as required by local
regulations.
TECHNICAL SPECIFICATIONS
Model
OM750ATLCD
Capacity (VA)
750VA
Input
Voltage Range
Frequency
Output
On Battery Output
Voltage
On Battery Output
Frequency
Overload Protection
Physical
Outlets-total
Outlets-Battery &
Surge Protected
Outlets-SurgeOnly
Protected
Dimensions(W XH X
D)mm
Weight (kg)
4.0
Battery
Sealed Maintenance
Free Lead Acid
RBP0043X 1
Battery
Typical Recharge
Time
Warning Diagnostics
Indicators
Power On, UPS Status Display, Capacity Display, Digital Value Display
Audible Alarms
Environmental
Operating
Temperature
Operating Relative
Humidity
Communication
®
PowerPanel
Personal Edition
Windows 7/ Windows 8/Vista/XP/2000/Server 2003, Linux
Software
Management
Auto-Charger
Auto-Restart
USB
）
OM900ATLCD
OM1500ATLCD
900VA
82~148Vac
50/60Hz(Auto Sensing)
Simulated Sine Wave at 120Vac +/-10%
50/60 Hz +/-1Hz
Breaker/Internal Current Limiting
6
3
3
96 X 138 X 286
148 X 178 X 298
4.9
RBP0110X 1
RBP0089X 2
8 Hours
On Battery, Low Battery, Overload
0C to 40C
0 to 90%
Yes
Yes
Yes
DEFINITIONS FOR ILLUMINATED LCD INDICATORS
LCD Indication
Line mode
Select SW
Press
Initial
1st
2nd
3rd
4th
5th(Return)
Press >3sec
(Sound Disable)
Press >3sec
again
(Sound Enable)
(Overload)
"V" : Illuminated,
"X" : Not Illuminated,
Battery mode
Select SW
Press
Initial
1st
2nd
3rd
4th
5th(Return)
Press >3sec
(Sound Disable)
Press >3sec
again
(Sound Enable)
(Overload)
"V" : Illuminated,
"X" : Not Illuminated,
Problem
The UPS does
not perform
expected
runtime.
The UPS will not
turn on.
1500VA
Outlets do not
provide power to
equipment
8
4
PowerPanel®
4
Personal Edition
is inactive
9.3
UPS Status Display
Capacity Display
Load
Battery
Cap.
Cap.
V
X
--
X
V
X
V
X
--
X
V
X
V
X
--
X
V
X
V
X
--
X
X
V
V
X
--
X
V
X
V
X
--
X
V
X
V
X
V
X
--
--
V
X
X
X
--
--
V
X
--
V
--
--
"--" : Either
UPS Status Display
Capacity Display
Load
Battery
Cap.
Cap.
X
V
--
X
X
V
X
V
--
X
X
V
X
V
--
X
V
X
X
V
--
X
X
V
X
V
--
X
X
V
X
V
--
X
X
V
X
V
V
X
--
--
X
V
X
X
--
--
X
V
--
V
--
--
"--" : Either
TROUBLE SHOOTING
Possible Cause
Solution
Recharge the battery by leaving the UPS
Batteries are not fully charged.
plugged in.
Contact CyberPower Systems Technical
Battery is slightly worn out.
Support.
The on/off switch is designed
Turn the UPS off. Wait 10 seconds and then
to prevent damage by rapidly
turn the UPS on.
turning it off and on.
The unit is not connected to an
The unit must be connected to a
AC outlet.
120V50/60Hz outlet.
Contact CyberPower Systems Technical
The battery is worn out.
Support.
Contact CyberPower Systems Technical
Mechanical problem.
Support.
Turn the UPS off and unplug at least one
Circuit breaker is tripped due
piece connected equipment. Unplug the
to overload
power cord of the UPS then press the circuit
breaker knob.
Allow the unit to recharge for at least 4
Batteries are discharged
hours.
Unit has been damaged by a
Contact CyberPower Systems Technical
surge or spike.
Support.
Connect the serial/USB cable to the UPS
The serial/USB cable is not
unit and an open serial port on the back of
connected.
the computer. You must use the cable that
came with the unit.
Shutdown your computer and turn the UPS
The unit is not providing
off. Wait 10 seconds and turn the UPS back
battery power.
on. This should reset the unit.
For more information, visit
www.cyberpower.com
All rights reserved. Reproduction without permission is prohibited.
Digital Value Display
Input
Output
Run
%
%
Voltage
Voltage
Time
of Load
of Batt.
V
V
V
V
V
V
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Digital Value Display
Input
Output
Run
%
%
Voltage
Voltage
Time
of Load
of Batt.
V
V
V
V
V
V
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Publicidad
