Technical Data; Before Starting The Equipment - EINHELL TE-PL 900 Manual De Instrucciones Original

4. Technical data

Mains voltage: ................................ 230 V ~ 50 Hz
Power input: ............................................... 900 W
Idling speed: ..................................... 15000 min
Chip depth: .............................................. 0-3 mm
Rebate depth: ........................................ 0-18 mm
Plane width: .............................................. 82 mm
Protection class: ............................................ II/
Weight: .......................................................3.2 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L sound pressure level ........................ 94 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ........................ 105 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Vibration emission value a
K uncertainty = 1.5 m/s
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
Anl_TE_PL_900_SPK9.indb 18 Anl_TE_PL_900_SPK9.indb 18
-1
= 3.61 m/s
2
h
2
- 18 -
GB
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
Caution! For safety reasons, the electric plane
must not be operated with the storage compart-
ment for accessories (9) inserted.
5.1 Adjusting the chip depth (Fig. 4/Item 1)
You can adjust the chip depth in steps of 0.1 mm
from 0 to 3 mm by turning the setting knob for the
chip depth (1).
Turn the setting knob for the chip depth (1) in a
clockwise direction to set a greater chip depth.
Greater chip depth
Turn the setting knob for the chip depth (1) in a
counter-clockwise direction to set a lower chip
depth. Lower chip depth
After fi nishing work, set the chip depth so that the
knives are lowered and thus protected from da-
mage. Turn the setting knob for the chip depth to
position "0" for this purpose.
20.08.2019 13:47:45 20.08.2019 13:47:45