Declaration Of Conformity; Specified Conditions Of Use; General Safety Information; Special Safety Instructions - Metabo S 18 LTX 115 Manual De Instrucciones

Original operating instructions

1. Declaration of Conformity

We, being solely responsible, hereby declare that
these burnishing machines, identified by type and
serial number *1), meet all relevant requirements of
directives *2) and standards *3). Technical
documents for *4) - see page 3.

2. Specified Conditions of Use

The burnishing machine is suited for
• burnishing, deadening, structuring and brushing,
• polishing and smoothing,
• sanding and deburring the following materials:
• metal, wood and plastics.
It is for dry processing only.
The user bears sole responsibility for any damage
caused by inappropriate use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.

3. General Safety Information

Pay attention to all parts of the text that
are marked with this symbol for your own
protection and for the protection of your
power tool!
WARNING – Reading the operating
instructions will reduce the risk of injury.
WARNING Read all safety warnings and
instructions. Failure to follow all safety
warnings and instructions may result in an electric
shock, fire and/or serious injury.
Keep all safety instructions and information for
future reference.
Pass on your power tool only together with these
documents.

4. Special Safety Instructions

4.1 General Safety Recommendations
for grinding, sanding, wire brushing,
polishing and cutting-off operations:
a) This power tool is intended to function as a
sander, wire brush or polisher. Read all safety
warnings, instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
b) Operations such as grinding or cutting-off
are not recommended to be performed with
this power tool. Operations for which the power
tool was not designed may create a hazard and
cause personal injury.
c) Do not use accessories which are not
specifically designed and recommended by the
tool manufacturer. Just because the accessory
can be attached to your power tool, it does not
assure safe operation.
d) The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
e) The outside diameter and the thickness of
your accessory must be within the capacity
rating of your power tool. Incorrectly sized
accessories cannot be adequately guarded or
controlled.
f) Threaded mounting of accessories must
match the sanding spindle thread. For
accessories mounted by flanges, the arbour
hole of the accessory must fit the locating
diameter of the flange. Accessories that do not
match the mounting hardware of the power tool will
run out of balance, vibrate excessively and may
cause loss of control.
g) Do not use a damaged accessory. Before
each use inspect the accessory such as
abrasive wheels for chips and cracks, backing
pad for cracks, tear or excess wear, wire brush
for loose or cracked wires. If a power tool or
accessory is dropped, inspect for damage or
install an undamaged accessory. After
inspecting and installing an accessory,
position yourself and bystanders away from
the plane of the rotating accessory and run the
power tool at maximum no-load speed for one
minute. Damaged accessories will normally break
apart during this test time.
h) Wear personal protective equipment.
Depending on application, use face shield,
safety goggles or safety glasses. As
appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments. The eye protection must be
capable of stopping flying debris generated by
various operations. The dust mask or respirator
must be capable of filtrating particles generated by
your operation. Prolonged exposure to high
intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from
work area. Anyone entering the work area must
wear personal protective equipment. Fragments
of workpiece or of a broken accessory may fly away
and cause injury beyond immediate area of
operation.
j) Hold the power tool by the insulated gripping
surfaces only when performing an operation
where the accessory may contact hidden
wiring or its own cord (for SE 17-200 RT).
Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live"
and shock the operator.
k) Position the cord clear of the spinning
accessory. If you lose control, the cord may be cut
or snagged and your hand or arm may be pulled into
the spinning accessory.
ENGLISH en
11