Metabo W 9-125 Quick Manual Original página 16

en
ENGLISH
Original instructions
1. Declaration of Conformity
We, being solely responsible: Hereby declare that
these angle grinders, identified by type and serial
number *1), meet all relevant requirements of
directives *2) and standards *3). technical
documents for *4) - see Page 4.
For UK only:
We as manufacturer and authorized person to
compile the technical file, see *4) on page 4,
hereby declare under sole responsibility that these
angle grinders, identified by type and serial number
*1) on page 3, fulfill all relevant provisions of
following UK Regulations *2) S.I. 2016/1091, S.I.
2008/1597, S.I. 2012/3032 and Designated
Standards EN 60745-1:2009+A11:2010, EN
60745-2-3:2011+A2:2013+A11: 2014+A12:
2014+A13:2015, EN IEC 63000:2018.
2. Specified Use
The angle grinders, when fitted with original Metabo
accessories, are suitable for grinding, sanding,
abrasive cutting-off operations and wire brushing
metal, concrete, stone and similar materials without
the use of water.
WEV 15-125 Quick HT, WEV 17-125 Quick Inox,
WEV 17-125 Quick Inox RT is additionally suited for
light polishing work. We recommend using our
angle polisher for demanding polishing work in
continuous operation.
Machines with the designation WEV are particularly
suited for working with wire brushes due to
thumbwheel for speed selection.
The user bears sole responsibility for any damage
caused by inappropriate use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.
3. General Safety Instructions
For your own protection and for the
protection of your power tool, pay
attention to all parts of the text that are
marked with this symbol!
WARNING – Reading the operating
instructions will reduce the risk of injury.
WARNING Read all safety warnings and
instructions. Failure to follow all safety
warnings and instructions may result in electric
shock, fire and/or serious injury.
Keep all safety instructions and information for
future reference.
Pass on your power tool only together with these
documents.
16
4. Special Safety Instructions
4.1 Safety Warnings Common for Grinding,
Sanding, Wire Brushing or Abrasive
Cutting-Off Operations:
Use
a) This power tool is intended to function as a
grinder, sander, wire brush or cut-off tool. Read
all safety warnings, instructions, illustrations
and specifications provided with this power
tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious
injury. WEV 15-125 Quick HT, WEV 17-125 Quick
Inox, WEV 17-125 Quick Inox RT can also be used
as polishing tool.
b) Operations such as polishing are not
recommended to be performed with this power
tool. Operations for which the power tool was not
designed may create a hazard and cause personal
injury. (Does not apply to WEV 15-125 Quick HT,
WEV 17-125 Quick Inox, WEV 17-125 Quick Inox
RT.)
c) Do not use accessories which are not
specifically designed and recommended by the
tool manufacturer. Just because the accessory
can be attached to your power tool, it does not
assure safe operation.
d) The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
e) The outside diameter and the thickness of
your accessory must be within the capacity
rating of your power tool. Incorrectly sized
accessories cannot be adequately guarded or
controlled.
f) Treaded mounting of accessories must
match the grinder spindle thread. For
accessories mounted by flanges, the arbour
hole of the accessory must fit the locating
diameter of the flange. Accessories that do not
match the mounting hardware of the power tool will
run out of balance, vibrate excessively and may
cause loss of control.
g) Do not use a damaged accessory. Before
each use inspect the accessory such as
abrasive wheels for chips and cracks, backing
pad for cracks, tear or excess wear, wire brush
for loose or cracked wires. If power tool or
accessory is dropped, inspect for damage or
install an undamaged accessory. After
inspecting and installing an accessory,
position yourself and bystanders away from
the plane of the rotating accessory and run the
power tool at maximum no-load speed for one
minute. Damaged accessories will normally break
apart during this test time.
h) Wear personal protective equipment.
Depending on application, use face shield,
safety goggles or safety glasses. As
appropriate, wear dust mask, hearing