Installation Steps - Steinberg Systems SBS-PF-300/50 Manual De Instrucciones

Please read the operating instruction before using.
ATTENTION
Thanks for purchasing our scale. Pls pay attention before using the scale:
1.
Please keep scale dry, Don't put it in sun shines directly, over high or over low
temperatures or high humidity, high dust or seriously shaken place.
2.
Don't rush the platform by heavy object, it will destroy load cell.
3.
When you put overload goods in the scale, it will alarms and display "FULL", Plea-
se remove the goods at once.
4. It should work in stable voltage, higher or lower will cause problem.
5.
It work on AC , plug power supply. Please remove the plug if long time not use it.
6.
When you clear the dirty on the scale, please use wet cloth, don't immerse it in
the water which will cause short of circuit.
7.
Please keep the scale clean and dry.
FEATRUES
EN
1.
Power supply: AC 230V or 110V, and DC 4V or 6V (Built-in rechargeable batte-
ry). Scale can work when charging battery.
2.
Accumulate operation(1-99 times)
3.
Work temperature 0°~40°
4.
Work Humidity: <85%R.H.
5.
Display windows: Weight window: 5digits
Unit price window: 5 digits
Total price window: 6 digits

INSTALLATION STEPS

1.
Remove the packing, take out the platform, stainless steel pole, display indicator,
and put the scale in flat place.
2. screw the pole on platform well.
3.
Adjust four feet under the platform.
4.
To connect the wire of meter with the cable which conducted from the platform
(by the way that combine 2 plugs from such 2 wires), then fix the meter on the
pole. So that when you turn on the switch of meter, the scale can run fine.
8
OPERATION
Make sure the scale on the flat stable place, then turn on the scale.
1. When turn on the scale, the "ZERO" and "STAB" will be activated.
the indicator display in both ZERO and STAB before you weight goods,otherwise
you can't get the correct weight number.
2. BACK LIGHT key : Press this key of back light, the LCD light will be ON, press
it again, the LCD light will be OFF. After LCD light is ON, if without any object
on platform, the back light will be turned off automatically within 3 seconds to
power saving function.
3. Zero key: Zeroes the number in weight window( range: <2%FS). If the TARE
function activated, ZERO function is disabled.
4. TARE Key:
• (1)To activate TARE: Press this key, TARE indicator displaying and weight win-
dow showing 0.000
• (2) To disable TARE: the weight window will show negative number when
the object removed, then press the key of TARE, the ZERO will be indicated
by arrow, and window of weight showing 0, that means TARE disabled. TARE
range full Capacity
5. [0]-[9] key: The Numeric key(0-9) is used for setting unit price date.
6. Add Key: When weight, it will store and accumulate the value of weight and
amount.
• Put goods in the Platform, the weight will appear on the WEIGHT window,
you can press numeric key input unit price, the TOTAL PRICE window will
show this first goods amount.
• now if you press Add , then the unit price will show: Add.1 Please must
remove this goods (otherwise can't continue), put another goods, you can
press numeric key input unit price, then the three window show new values,
Now the TOTAL PRICE window will show second goods amount.
• Press Add again, then the window of UNIT PRICE will show: Add 2
• now the TOTAL PRICE window is the value for 2 items. If you need to
weight more items You can repeat this step again and again
Note: the total accumulated items should not over 99 items. when you want
to cancel this function, just press the C key on panel
Make sure
9
EN