Specific Safety Rules - RIDGID R4112 Manual Del Operador

GENERAL SAFETY RULES
 INSPECT TOOL CORDS PERIODICALLY. If damaged,
have repaired by a qualified service technician at an
authorized service facility. Repair or replace a damaged
or worn cord immediately. Stay constantly aware of cord
location and keep it well away from the rotating blade.
 INSPECT EXTENSION CORDS PERIODICALLY and
replace if damaged.
 POLARIZED PLUGS. To reduce the risk of electric shock,
this tool has a polarized plug (one blade is wider than
the other). This plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician
to install the proper outlet. Do not change the plug in any
way.
 KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND
GREASE. Always use a clean cloth when cleaning. Never
use brake fluids, gasoline, petroleum-based products, or
any solvents to clean tool.
 STAY ALERT AND EXERCISE CONTROL. Watch what
you are doing and use common sense. Do not operate
tool when you are tired. Do not rush.
 DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
ON AND OFF. Have defective switches replaced by an
authorized service center.
 USE ONLY CORRECT BLADES. Do not use blades with
incorrect size holes. Never use blade washers or blade

SPECIFIC SAFETY RULES

 FIRMLY CLAMP OR BOLT your tool to a workbench or
table at approximately hip height.
 KEEP HANDS AWAY FROM CUTTING AREA. Do not
reach underneath work or in blade cutting path with your
hands and fingers for any reason. Always turn the power
off.
 ALWAYS SUPPORT LONG WORKPIECES while cutting
to minimize risk of blade pinching and kickback. Saw may
slip, walk or slide while cutting long or heavy boards.
 ALWAYS USE A CLAMP to secure the workpiece when
possible.
 BE SURE THE BLADE CLEARS THE WORKPIECE.
Never start the saw with the blade touching the workpiece.
Allow motor to come up to full speed before starting cut.
bolts that are defective or incorrect. The maximum blade
capacity of your saw is 10 in.
 B E F O R E M A K I N G A C U T , B E S U R E A L L
ADJUSTMENTS ARE SECURE.
 BE SURE BLADE PATH IS FREE OF NAILS. Inspect for
and remove all nails from lumber before cutting.
 NEVER TOUCH BLADE or other moving parts during
use.
 NEVER START A TOOL WHEN ANY ROTATING
COMPONENT IS IN CONTACT WITH THE WORKPIECE.
 DO NOT OPERATE A TOOL WHILE UNDER THE
INFLUENCE OF DRUGS, ALCOHOL, OR ANY
MEDICATION.
 WHEN SERVICING use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
 USE ONLY RECOMMENDED ACCESSORIES listed in
this manual or addendums. Use of accessories that are not
listed may cause the risk of personal injury. Instructions for
safe use of accessories are included with the accessory.
 DOUBLE CHECK ALL SETUPS. Make sure blade is tight
and not making contact with saw or workpiece before
connecting to power supply.
 MAKE SURE THE MITER TABLE AND SAW ARM
(BEVEL FUNCTION) ARE LOCKED IN POSITION
BEFORE OPERATING YOUR SAW. Lock the miter table
by pushing the miter lock lever down. Lock the saw arm
(bevel function) by securely tightening the bevel lock knob.
 NEVER USE A LENGTH STOP ON THE FREE SCRAP
END OF A CLAMPED WORKPIECE. NEVER hold onto or
bind the free scrap end of the workpiece in any operation.
If a work clamp and length stop are used together, they
must both be installed on the same side of the saw table to
prevent the saw from catching the loose end and kicking
up.
 NEVER cut more than one piece at a time. DO NOT
STACK more than one workpiece on the saw table at a
time.
4