Pioneer DEH-6250BT Manual De Instrucciones página 19

Operating this unit
1 Press M.C. to display the setting mode.
2 Press M.C. to select the segment of the clock dis-
play you wish to set.
Hour—Minute
As you select segments of the clock display, the
selected segment flashes.
3 Turn M.C. to adjust the clock.
Clock (clock on/off setting)
1 Press M.C. to turn the clock display on or off.
FM step (FM tuning step)
The FM tuning step employed by seek tuning can be
switched between 100 kHz, the preset step, and 50
kHz.
If seek tuning is performed in 50 kHz steps, stations
may be tuned in imprecisely. Tune in the stations with
manual tuning or use seek tuning again.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the FM tuning step.
50kHz (50 kHz)—100kHz (100 kHz)
3 Press M.C. to confirm the selection.
AM step (AM tuning step)
The AM tuning step can be switched between 9 kHz,
the preset step, and 10 kHz. When using the tuner in
North, Central or South America, reset the tuning
step from 9 kHz (531 kHz to 1 602 kHz allowable) to 10
kHz (530 kHz to 1 640 kHz allowable).
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the AM tuning step.
10kHz (10 kHz)—9kHz (9 kHz)
3 Press M.C. to confirm the selection.
Warning (warning tone setting)
If the front panel is not detached from the head unit
within four seconds of turning off the ignition, a warn-
ing tone sounds. You can turn off the warning tone.
1 Press M.C. to turn the warning tone on or off.
AUX (auxiliary input)
Activate this setting when using an auxiliary device
connected to this unit.
1 Press M.C. to turn auxiliary setting on or off.
USB PnP (plug and play)
Black plate (19,1)
This setting allows you to switch your source to USB/
USB-iPod automatically.
1 Press M.C. to turn the plug and play on or off.
! ON – When USB storage device/iPod is con-
nected, the source is automatically switched
to USB/USB-iPod. If you disconnect your USB
storage device/iPod, this unit's source is
turned off.
! OFF – When USB storage device/iPod is con-
nected, the source is not switched to USB/
USB-iPod automatically. Please change the
source to USB/USB-iPod manually.
Brightness (display brightness setting)
1 Press M.C. to display the setting mode.
2 Turn M.C. to switch the brightness setting.
High (high)—Low (low)
3 Press M.C. to confirm the selection.
SW control (rear output and subwoofer setting)
The rear speaker leads output (Rear SP:) and RCA
output (Preout:) of this unit can be used for full-
range speaker (Rear SP: :Full/Preout: :Rear) or sub-
woofer (Rear SP: :SUBW/Preout: :SUBW) connection.
If you switch to Rear SP: :SUBW, you can connect a
rear speaker lead directly to a subwoofer without
using an auxiliary amp.
Initially, Rear SP: is set for rear full-range speaker con-
nection (Full). When Rear SP: :Full is selected, you
can connect the RCA output to a subwoofer. In this
case, you can select whether to use the subwoofer
controller's (low pass filter, phase) built-in Preout: :
SUBW or the auxiliary Preout: :Rear.
1 Press M.C. to display the setting mode.
2 Press M.C. to cycle between as following:
Rear SP:/Preout:—Full (SUBW)/SUBW(Rear)
3 Turn M.C. to change the setting.
Rear SP:: Full—SUBW
Preout:: SUBW—Rear
! Even if you change this setting, there is no
output unless you turn the subwoofer output
on (refer to SW setting 1 (subwoofer on/off
setting) on page 17).
! If you change this setting, subwoofer output
in the audio menu will return to the factory
settings.
DEMO (demo display setting)
<YRD5316-B/S>19
Section
02
19
En