Publicidad
6209/P
The instructions manual can be downloaded from the website
www.vimar.com
Description
Article 6209 is a Petrarca Series entryphone for "Due Fili Plus" audio and video
door entry systems. It is equipped as standard with 5 pushbuttons, one to open
the door lock, two to control relays 1 and 2 and 2 which can be used for the
intercom calls function. The entryphone can be fitted with an additional 2 pairs
of pushbutton art. 692P (692P/M or 692P/R), for auxiliary services or intercom
calls, and the accessory art. 6153/682 for: call volume adjustment, call signal
mute, call rejected luminous indicators, signal to indicate unanswered calls, si-
gnal to indicate services not available and luminous signal for gate/door open.
The entryphone can be wall-mounted or installed as desktop version using the
conversion kit art. 6140 or 6A40.
Connection and connector terminal board
1, 2)
BUS line
4, 6P)
Connection for door call pushbutton.
5, 6S)
Connection of additional door ringer.
VARIAT.) Connection for module art. 6153/682
T1)
1st pair of pushbuttons art. 692P (included)
T2)
2nd pair of pushbuttons art. 692P (included)
T3)
3rd pair of pushbuttons art. 692P (optional accessory - not included)
T4)
4th pair of pushbuttons art. 692P (optional accessory - not included)
Fig. 1
BL
RO
BI
A+
A-
CA
TR1
RESET
PRG.
SERIALE
Lock
T1
T2
T3
T4
Settings
The call volume can be adjusted by moving the loudspeaker wire from connector
A+ (high) to A- (low); otherwise use accessory art. 6153/682, leaving the loudspe-
aker wire connected to connector A-.
4
VARIAT.
For art. 6153/682
TR2
T1
T2
T3
T4
Video signal
stabilisation
1
2
4
5
6S
6P
Programming
There are three entryphone programming modes: assignment of an identification
code or call code (indispensable), assignment of a secondary identification code
(for entryphones associated with a master entryphone), programming of pushbut-
tons for auxiliary services and intercom calls (when necessary). Programming
must be carried out with the system switched on, without active communication
and only after the entryphones/monitors have been connected to the system and
the entrance panels have been programmed.
Identification code programming
The identification code is programmed by means of a main entrance panel (MA-
STER), already configured and present in the system. The entryphone is supplied
without an associated identification code. To verify this condition, press the lock
release pushbutton and the entryphone should emit a triple "Beep".
Warning: during programming of the entryphone/video entryphone, you
have only 30 seconds from the moment of entering entryphone/video en-
tryphone programming mode in which to press the call button on the en-
trance panel or to send the code.
Programming phase:
1) Remove the entryphone cover.
2) Press and hold the RESET pushbutton on the entryphone.
3) Press and hold the tab on the lock release pushbutton, together with the
RESET pushbutton.
4) Release the RESET pushbutton, keeping the lock release pushbutton pres-
sed.
5) After 2 seconds the entryphone emits a high tone and communication is
enabled with the panel.
6) Release the tab of the lock release pushbutton.
7) On pushbutton entrance panels, press the call button for the entryphone,
while on alphanumeric keypads, enter the call code and press pushbutton "
".
8) If the system contains an entryphone that already has the same associated
identification code, the panel emits a low tone and the operation will have to
be repeated from point 2.
9) Otherwise the code is associated with the entryphone and communication is
terminated.
Programming the secondary identification code
Programming of the secondary identification code is only required when more
than one entryphone is to be called simultaneously using the same pushbutton
or call code. The entryphones that are to ring simultaneously must be associated
with the same group. The "master" entryphone is programmed first by means of
the "identification code programming" procedure described above, while the addi-
tional group entryphones are programmed with the secondary identification code
(see table in the wiring diagrams section). The maximum number of entryphones
that can be associated with the same group, without using a 950C programmer,
is 3 plus the master unit.
Programming phase:
1) Remove the entryphone cover.
2) Press and hold the RESET pushbutton on the entryphone.
3) Press and hold the tab on the lock release pushbutton, together with the P1
and RESET pushbuttons.
4) Release the RESET pushbutton, keeping the other two pushbuttons pressed.
5) After 2 seconds the entryphone emits a high tone and communication is
enabled with the panel.
6) Release the tab on the lock release pushbutton and the P1 pushbutton
7) On pushbutton entrance panels, press the call button for the "master" en-
tryphone (already programmed), while on alphanumeric keypads, enter the
call code of the "master" entryphone and press pushbutton "
8) When the secondary code is associated with the entryphone, the communi-
cation is terminated.
To discover the number assigned, refer to the table in the wiring diagrams section.
Pushbutton programming
The entryphone is supplied with two pairs of the additional pushbuttons 692P,
for the default functions listed below. It is possible to fit a further 2 pairs of 692P
pushbuttons in the entryphone, connected to connectors T3-T4.
The default functions of the pushbuttons are as follows:
Pushbutton Connector
In program.
1st
T1
P1
2nd
T1
P2
EN
".
Default functions
Stair light
(1st relay of 1st actuator, art. 69RH)
Auxiliary
Publicidad
