Publicidad
Idiomas disponibles
Idiomas disponibles
Computed
kickback
angle
(CKA)
Table
BAR
MODEL
P/N
Length
330
952044795
20"
380
952044795
20"
330
530044833
22"
CHAIN
P/N
952051482
952051482
952051483
CKAwithout
chain brake
21 °
21 °
23 °
NOTE:
This
saw
complies
with
Federal
OSHA
regulations
for commercial
logging.
SAFETY
NOTICE:
Exposure
to
vibrations
through prolonged
use of gasoline
powered
hand
toots
could
cause
blood
vessel
or nerve
damage
in the
fingers,
hands,
and
joints
of
people
prone
to
circulation
disorders
or abnormal
swellings.
Prolonged
use
in cold weather
has
been
linked to blood vessel damage
in otherwise
healthy
people.
If symptoms
occur such as
numbness,
pain, loss of strength,
change
in
skin color or texture,
or loss of feeling
in the
fingers,
hands, or joints, discontinue
the use
of this tool and seek
medical
attention.
An
anti-vibration
system does not guarantee
the
avoidance
of these
problems.
Users
who
operate
power
tools
on a conth_ual
and
regular
basis
must
monitor
closely
their
physical
condition
and the condition
of this
tool.
SPECIAL
NOTICE:
Your saw is equipped
with a temperature
limiting muffler and spark
arresting
screen
which
meets
the
requirements
of California
Codes 4442 and
4443. All U.S.
forest land and the states of
California,
Idaho,
Maine,
Minnesota.
New
Jersey,
Oregon.
and Washington
require
many
internal
combustion
engines
to be
equipped
with a spark
arrestor
screen
by
law. If you operate a chain saw in a state or
locale where such regulations
exist, you are
legally
responsible
for
maintaining
the
operating
condition
of these parts. Failure to
do so is a violation
of the law. Refer to the
SERVICE
section
for maintenance
of the
Spark Arrestor.
Failure to follow atl Safety Rules and Precau-
tions can result in serious injury. If situations
occur which are not covered
in this manual,
use care and good judgement.
If you need
assistance,
contact your Authorized
Service
Dealer.
Protective
gloves
(not provided)
should
be
worn during assembly.
ATTACHING
TH E BAR & CHAIN
(If not
already
attached)
WARNING:
If received
assembled,
repeat all steps to ensure your saw is proper-
ly assembled
and all fasteners
are secure.
Always
wear
gloves
when
handling
the
chain. The chain
is sharp and can cut you
even when it is not moving!
• Loosen
and remove the chain brake nuts
and the chain brake from the saw.
• Remove
the plastic
shipping
spacer
(if
present).
_
hipping
Spacer
Assembly
_J
..._ .//
Tool \
Chain Brake/_:_
Chain Brake Nuts
_
@
• An adjusting
pin and screw
is used to ad-
just the tension
of the chain. It is very im-
portant when assembling
the bar, that the
pin located
on the adjusting
screw aligns
into a hole in the bar. Turning the screw will
move the adjustment
pin up and down the
screw. Locate this adjustment
before you
begin mounting
the bar onto the saw. See
illustration
below.
Adjustment
ssrew
• Turn
the
adjusting
screw
counterclock-
wise to move
the adjusting
pin almost
as
far as it will go to the rear. This should allow
the pin to be near the correct position. Fur-
ther adjustment
may be necessary
as you
mount the bar.
• Mount the bar as illustrated.
• Slide the bar toward the rear of the saw as
far as possible.
• Prepare
the chain by checking
the proper
direction.
Without
following
the illustration
it is easy to place the chain on the saw the
wrong direction.
Use the illustration
of the
chain to determine
the proper direction.
• Place the chain onto the sprocket
located
behind the clutch
drum
(see illustration).
Fit the chain
between
the teeth
in the
sprocket.
• Start at the top of the bar and fit chain into
groove around the guide bar.
• After chain is installed,
pull bar forward un-
til chain is snug in the groove
of the bar.
Publicidad
