Publicidad
Idiomas disponibles
Idiomas disponibles
Poulan Pro_; barand chain o ilis not
available,
use agood grade SAE 3 0 oil.
• Never use w aste oil for b ar and c hain lubri-
cation.
• Always stop t he engine before removing
the oil c ap.
Oil C ap
Fuel mix cap
IMPORTANT
Experience
indicates that alcohol-blended
fuels
(called
gasohol
or using
ethanol
or
methanol)
can attract moisture
which
leads
to separation
and formation
of acids during
storage.
Acidic
gas can damage
the fuel
system
of an engine while
in storage.
To
avoid
engine
problems,
the
fuel
system
shouM
be emptied
before
storage
for 30
days or longer.
Drain the gas tank, start the
engine and let it run untii the fuet lines and
carburetor
are empty.
Use fresh fuel next
season.
See STORAGE
section for addi-
tiona_ information.
_WARNING:
The
chain
must
not
move when the engine runs at idle speed. If
the chain moves at idle speed refer to CAR-
BURETOR
ADJUSTMENT
within
this
manual. Avoid contact with the muffler. A hot
muffler can cause serious burns.
To stop
the engine
move
the ON/STOP
switch
to the STOP position.
To start
the engine
hold the saw firmly on
the ground
as illustrated.
Make
sure
the
chain is free to turn without
contacting
any
object.
Use only 15"- 18" of rope per pull.
Hold saw firmly while pulling starter rope.
handle
Left hand
front
handle
Right foot through
rear handle
IMPORTANT
POINTS
TO REMEMBER
When pulling the starter rope, do not use the
full extent of the rope as this can cause the
rope to break,
Do not let starter
rope snap
back. Hold the handle and let the rope rewind
slowIy.
For cotd weather
starting,
start the unit at
FULL CHOKE;
allow the engine to warm up
before squeezing
the throttle trigger.
NOTE:
Do not cut material
with the choke/
fast idle lever at the FULL CHOKE
position.
STARTING
A COLD
ENGINE
(or
a
warm
engine
after
running
out
of
fuel)
• MoveON/STOPswitct_totheON
position.
• Pull the choke/fast
idle lever out to the full
extent.
ON/STOP
ON
SWITCH
STOP
CHOKE/FAST
IDLE LEVER
It(SIDE VIEW)
Choke/Fast
OFF
FULL
Idle Lever
• Press the throttle lock with your right hand.
Squeeze
and
hold
the
throttle
trigger;
Press and hoid the fast idle lock with your
forefinger;
release the throttle trigger.
NOTE:
If the throttle
trigger
is squeezed
during starting,
it will be necessary
to reset
the fast idle lock.
• Pull the starter rope quickly with your right
hand a maximum
of 10 times.
• Push the choke/fast
idle lever in complete-
ly (to the OFF CHOKE
position).
• Pull the starter rope quickly with your right
hand until the engine starts.
• Allow the engine to run for approximately
5
seconds.
Then, squeeze
and release the
throttle trigger to allow engine to return to
idle speed.
STARTING
A WARM
ENGINE:
• MoveON/STOPswitchtotheON
position.
• Press the throttle lock with your right hand.
Squeeze
and
hold
the
throttle
trigger;
Press and hold the fast idle lock with your
forefinger;
release the throttle trigger.
• Be sure choke/fast
idle lever is in the OFF
CHOKE
position.
• Pull the starter rope quickly with your right
hand until the engine starts.
• Squeezeand
releasethethrottletrigger
to
allow engine to return to idle speed.
DIFFICULT
STARTING
(or starting
a
flooded
engine)
The engine
may be flooded
with too much
fuel if it has not started after 10 pulls.
Flooded
engines can be cleared
of excess
fuel by following
the warm
engine
starting
procedure
listed
above.
Insure
the ON/
STOP switch
is in the ON position.
Starting
could require pulling the starter rope
handle many times depending
on how badly
the unit is flooded.
If engine fails to start refer
to the TROUBLESHOOTING
TABLE or call
1-800-554-6723.
Publicidad
