Switching On/Off - Twiins FF2 Manual De Instrucciones

TWIINS FF2
®
INSTRUCTION MANUAL
Welcome
Congratulations and thank you for purchasing a Twiins
FF2 device. This Bluetooth
designed to keep you connected to your phone and
listen to your favourite music while travelling on your
scooter or motorcycle.
The Twiins D2 system is compatible with all Bluetooth
®
devices that transmit audio (mobile phones, smart-
phones, GPS navigators and other devices) using the
profiles specified in the manual.
This device is designed so that it may be wholly inte-
grated into your helmet. It can be operated and paired
easily through a single control button (1b).
A single red/blue LED indicator (1a) serves to display
connection status, pairing, battery charging and low
battery. The Twiins
®
For better use of the Twiins
this manual and keep it in a safe place or find it at
www.twiins.com
Charging the Twiins
Before using your Twiins
you must charge the device completely.
Connect the terminal (3) to the provided USB cable (5)
and then connect the cable to a USB charging port.
While charging, the red LED light will switch on (1a) and
it will switch off once charging has been completed.
NOTE: Don't pull on the cable to disconnect it from the
USB port.
NOTE: As time goes by, batteries gradually lose their
charge. This is why it's important to charge the battery
fully before using the device and allow the battery to
use almost all of it's charge in between charging cycles.
WARNING:
If you plan to store your Twiins
for a long period of time, be sure to recharge it at least
once every six months to ensure perfect battery func-
tion.
8
device has been especially
®
D2 device weighs only 55 g.
FF2 device, please read
®
FF2
®
FF2 device for the first time,
®
Installation
The Twiins
®
move the side padding from the inside of the helmet (if it
can be removed) and place the devices (2) and (4) at the
®
height of your ears. The device is designed so that the
main unit with the boom microphone is placed on the
right side. The wire between devices (2) and (4) must be
stored inside the helmet, under the padding. In order
to affix the headphones, two Velcro pads are provided
®
(male and female) with an adhesive backing (7). In case
you need to use the Velcro, stick the male part of the
pad onto the device and the female part onto the inside
of the helmet.
Depending on the internal configuration of each type of
helmet, it may be necessary to use the entire Velcro pad
or only a part of it (see figure 2). In some cases, it may
only be necessary to stick the male part onto the device
as the inside of the helmet may have padding that can
serve as Velcro (female).
If needed, comfort pads (6) to place on the headphones
are also provided, in order to improve comfort against
your skin.
The charging cable (3) must be placed on the lateral-
back section of the helmet so as to facilitate access to
charge the device.
Place the microphone (1) on the front section of the hel-
met (close to and oriented towards your mouth, always
protecting the microphone with the padding).
Linking/Pairing
To use the Twiins
Bluetooth
®
phone, GPS navigator). While the device is switched
off, hold the control button (1b) until the LED indicator
(1a) begins flashing in Red and Blue. The mobile phone
or GPS navigator will find the device under the name
FF2. Select the FF2 device and, if necessary, enter the
access code: 0000.
® device
NOTE: Pairing is a process that only needs to be com-
pleted once. When the Twiins
ic device, both devices will connect automatically when
switched off and on.

Switching on/off

Switching on: press and hold the button (1b) for a few
seconds until the speaker provides an acoustic signal
FF2 is very easy to install into a helmet. Re-
FF2, it's necessary to pair it to the
®
device you wish to connect it to (mobile
FF2 is paired to a specif-
®