Technical Specifications - Twiins FF2 Manual De Instrucciones

and the LED indicator (1a) begins to flash in Blue.
Switching off: press and hold the control button (1b) for
a few seconds until the speaker provides an acoustic
signal and the LED indicator (1a) begins flashing in red
before the device powers off.
Call functions
When there is an incoming call, the speaker will provide
an acoustic signal.
Answering by pressing the button (1b): press the con-
trol button (1b) only once
Answering through a voice command: answer the call
by speaking any word out loud (e.g. "Answer!")
Ending a call: press the control button (1b) only once or
wait until the other person hangs up
Rejecting an incoming call: press the control button
(1b) twice, as soon as you hear the acoustic signal for
an incoming call
Redialling: press the control button (1b) twice. This de-
pends on the features and configuration of your mobile
phone.
Adjusting the volume
The Twiins FF2 device is pre-programmed with a vol-
®
ume level that allows for optimal listening at speeds of
up to 80 km/h (50 mph). To adjust the volume, use the
volume controls on the connected device.
Volume perception may vary depending on the position
and separation of the speakers from your ears, as well
as the type of helmet and motorcycle, external condi-
tions and other factors.

Technical Specifications

Bluetooth : 2.1 Class 2
®
Profiles: A2DP, HSP, HFP, EDR
Battery: Lithium polymer, allowing for up to 7 hours of
talk time and 200 hours of standby time (depending on
use and configuration of the device)
Compatible with Twiins
Twiins D2HSAi intercoms
®
Ready to operate as an intercom: you can pair your
Twiins FF2 device to a Twiins
®
SAi and activate the intercom mode, without losing the
hands-free features for your phone.
Dual link: While connected to a Twiins
D3 and
®
D3 or a Twiins D2H-
® ®
D3 or Twiins
® ®
D2HSAi, if you receive a call, the intercom function will
stop and then resume when the call ends.
Care and maintenance
The Twiins FF2 device uses components with the lat-
®
est technology and is manufactured to high standards.
To keep your device from inadvertently becoming dam-
aged, please read the following recommendations care-
fully:
• Do not attempt to open any of the system compo-
nents, since the electronic parts inside it may become
damaged. Do not attempt to open or change the bat-
tery as it may be dangerous.
• Keep the Twiins FF2 out of the reach of children.
®
• Keep the Twiins FF2 in a dry place. Humidity and
®
condensation may damage the electronic circuits.
• Avoid exposing the device to extreme temperatures.
Intense cold may create condensation inside the com-
ponents as these warm up. Extreme heat may damage
the battery, circuits or casings.
• Do not drop, hit or bend the components as the inter-
nal circuits may become damaged.
• Do not paint or decorate the Twiins
ings may become damaged or impede correct opera-
tion.
• Do not use chemical products, solvents or detergents
to clean the Twiins FF2 as these may damage the de-
®
vice.
Troubleshooting
If you cannot connect your Twiins
mobile phone:
• Make sure the Twiins FF2 is switched on
®
• Make sure your mobile phone is switched on and
Bluetooth has been turned on
®
• Make sure both devices are paired
• Make sure the Twiins
®
phone are not more than 10 metres (32 ft.) apart
If, after this, you're still not able to pair or use the Twiins
FF2 with your mobile phone, please contact the retailer
where you purchased the product.
FF2 as the cas-
®
FF2 device to your
®
FF2 device and your mobile
®
9