Ec Declaration Of Conformity; Technical Data - EUCHNER SGP Serie Manual De Instrucciones

Operating Instructions
Safety Switches SGP...
Exclusion of liability and warranty
In case of failure to comply with the conditions for
correct use stated above, or if the safety instruc-
tions are not followed, or if any servicing is not
performed as required, liability will be excluded and
the warranty void.
Notes about
The following information applies to devices
with cable entry:
For use and applications as per the requirements
of , a copper wire for the temperature range
60/75 °C is to be used.
The following information applies to devices
with plug connector:
For use and applications as per the requirements of
, a class 2 power supply according to UL1310
must be used. Connection cables for safety switches
installed at the place of use must be separated
from all moving and permanently installed cables
and un-insulated active elements of other parts
of the system which operate at a voltage of over
150 V. A constant clearance of 50.8 mm must be
maintained. This does not apply if the moving cables
are equipped with suitable insulation materials which
possess an identical or higher dielectric strength
compared to the other relevant parts of the system.
Version Switching contacts
SGP.-538H...
2 NC contacts
SGP.-2121H...
4 NC contacts
SGP.-2131H...
3 NC contacts + 1 NO contact
SGP.-3131H...
2 NC contacts + 2 NO contacts
Figure 2: Switching elements and switching functions

EC declaration of conformity

The manufacturer named below herewith declares
that the product fulfills the provisions of the direc-
tive(s) listed below and that the related standards
have been applied.
EUCHNER GmbH + Co. KG
Kohlhammerstr. 16
D-70771 Leinfelden-Echterdingen
Directives applied:
Machinery directive 2006/42/EC
f
Standards applied:
EN 60947-5-1:2004 + Cor.:2005 + A1:2009
f
EN 1088:1995+A2:2008
f
EN 14119:2013
f
The original EC declaration of conformity can also
be found at: www.euchner.de
Service
If service support is required, please contact:
EUCHNER GmbH + Co. KG
Kohlhammerstraße 16
D-70771 Leinfelden-Echterdingen
Service telephone:
+49 711 7597-500
Fax:
+49 711 753316
E-mail:
support@euchner.de
Internet:
www.euchner.de
Door closed Door open
21 22 21 22
11 12
11 12
41 42
41 42
33 34
33 34
21 22
21 22
11 12
11 12
41 42
41 42
33 34
33 34
21 22
21 22
11 12
11 12
41 42
41 42
33 34
33 34
21 22
21 22
13 14
13 14

Technical data

Parameter
Housing material
Degree of protection
acc. to IEC 60529
SGP1... (cable entry)
SGP2... (plug connector)
Mechanical life
Ambient temperature
Degree of contamination
(external, acc. to EN 60947-1)
Installation position
Approach speed, max.
Extraction force
Retention force
Actuating force, max.
Actuation frequency
Switching principle
Contact material
Connection
SGP1...
SGP2...SR6
SGP2...SR11
Conductor cross-section
(flexible/rigid)
SGP1...
SGP2...SR6
SGP2...SR11
Operating voltage for optional
LED indicator
(only SGP...538H)
Conditional short-circuit
current
Switching voltage, min.
at 10 mA
Switching current, min.,
at 24 V
Short circuit protection
(control circuit fuse)
acc. to IEC 60269-1
Conv. thermal current I
Utilization category
acc. to EN 60947-5-1
AC-15
DC-13
Rated insulation voltage
Rated impulse withstand
voltage
Reliability values acc. to EN ISO 13849-1
B
10d
Terminal assignment
with plug connector SR6
(LED indicator with
full wiring options optional)
5
2.
1
1.
3
Ordinal numbers
of switching elements
Terminal assignment with plug
connector SR11
4.
7
3.
5
2.
3
1.
1
Ordinal numbers
of switching elements
5
Value
Reinforced thermoplastic
IP67
IP65
2 x 10 operating cycles
6
-20 ... +80 °C
3 (industrial)
Any
20 m/min
25 N
10 N
25 N
6,700/h
Slow-action switching contact
Silver alloy, gold flashed
Cable entry M20 x 1.5
Plug connector SR6, 6-pin+PE
Plug connector SR11, 11-pin+PE
0.34 ... 1.5 mm²
0.5 ... 1.5 mm²
0.5 mm²
L060 12 - 60 V
L110 110 V
L220 230 V
100 A
12 V
1 mA
4 A gG
4 A
th
SGP1.../
SGP2...SR11
SGP2...SR6
4 A 230 V
4 A 24 V
U = 250 V
i
U = 2.5 kV U
imp
3 x 10
6
Connector illustration
plug connector SR6
View of safety switch connection side
6
2
2.
2
3
1.
4
4
Connector illustration
plug connector SR12
View of safety switch connection side
PE
4.
8
8
11
3.
6
7
2.
4
6
1.
2
5
10
4 A 50 V
4 A 24 V
U = 50 V
i
= 1.5 kV
imp
1
6
5
1
9
2
3
4