General Safety Rules; Before Use; Led Indicators - Hilti PRE 38 Manual De Instrucciones

f) Precautions must be taken to ensure that persons do
not stare directly into the beam.
g) The laser beam must not be allowed to project bey-
ond the controlled area.
h) When not in use, laser tools should be stored in a
place to which unauthorized persons have no access.

5.4 General safety rules

a) Check the condition of the tool before use. If the
tool is found to be damaged, have it repaired at a
Hilti service center.
b) The user must check the accuracy of the tool
after it has been dropped or subjected to other
mechanical stresses.
c) When the tool is brought into a warm environment
from very cold conditions, or vice-versa, allow it
to become acclimatized before use.
d) If mounting on an adapter, check that the tool is
screwed on securely.
e) Keep the laser exit aperture clean to avoid meas-
urement errors.
f) Although the tool is designed for the tough condi-
tions of jobsite use, as with other optical and elec-
tronic instruments (e.g. binoculars, spectacles,
cameras) it should be treated with care.
g) Although the tool is protected to prevent entry
of dampness, it should be wiped dry each time
before being put away in its transport container.
h) Check the tool before using it for important meas-
uring work.
i) Check the accuracy of the measurements several
times during use of the tool.
j) Use the AC adapter only for connecting to the AC
supply.
k) Check to ensure that the tool and AC adapter do
not present an obstacle that could lead to a risk
of tripping and personal injury.
Ensure that the workplace is well lit.
l)
m) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.

6 Before use

NOTE
The tool may be operated only with the Hilti PRA 87 bat-
tery pack, which has been manufactured in accordance
with IEC 60285, or with 4 size D alkaline batteries. The
PRA 88 battery holder must be used in accordance with
the applicable instructions.
n) Check the condition of the extension cord and
replace it if damage is found. Do not touch the AC
adapter if the extension cord or AC adapter are
damaged while working. Disconnect the supply
cord plug from the power outlet. Damaged supply
cords or extension cords present a risk of electric
shock.
o) Do not expose the supply cord to heat, oil or sharp
edges.
p) Never operate the AC adapter when it is dirty or
wet. Dust (especially dust from conductive mater-
ials) or dampness adhering to the surface of the
AC adapter may, under unfavorable conditions,
lead to electric shock. Dirty or dusty tools should
thus be checked at a Hilti service center at regular
intervals, especially if used frequently for working
on conductive materials.
q) Avoid touching the contacts.
5.4.1 Battery tool use and care
a) Check that the tool is switched off before fitting
the battery. Use only the Hilti battery approved for
use with this tool.
b) Do not expose batteries to high temperatures or
fire. This presents a risk of explosion.
c) Do not disassemble, squash or incinerate batter-
ies and do not subject them to temperatures over
75°C. A risk of fire, explosion or injury through con-
tact with caustic substances may otherwise result.
d) Avoid ingress of moisture. Moisture may cause a
short circuit resulting in a risk of burning injury or fire.
e) Do not use batteries other than those approved
for use with the applicable tool or appliance. Use
of other batteries or use of the battery for purposes
for which it is not intended presents a risk of fire and
explosion.
f) Observe the special instructions applicable to the
transport, storage and use of Li-ion batteries.
g) Avoid short-circuiting the battery.Before inserting
the battery in the tool, check that the terminals of
the battery and the tool are free from foreign objects.
Short-circuiting the battery terminals presents a risk
of fire, explosion or contact with caustic substances.
h) Do not charge or continue to use damaged bat-
teries (e.g. batteries with cracks, broken parts,
bent or pushed-in and/or pulled-out contacts).
i) Use only the PRA 89 AC adapter to power the
tool or charge the battery pack. Failure to observe
these points may result in damage to the tool.

6.1 LED indicators

Please refer to section 2 "Description".
en
23