Tabla de contenido
Publicidad
2. Transmitted Data
[EXT]
It means the message that can transmit the each part of the External upper/
lower/pedal.
[ORGAN]
It means the message that can transmit the each part of the Organ Voices.
[ORCH]
It means the message that can transmit the each part of the Orchestral
Voices.
[CTRL]
It means the message that can transmit a MIDI channel specified by Control
MIDI Channel.
*
Messages for the external upper/lower/pedal part will be transmitted on the each channels
specified by External MIDI Channel (SYSTEM MIDI MENU -> Ext MIDI Ch).
*
Messages for the external upper/lower/pedal part will be transmitted when the [EXT UPPER]/
[EXT LOWER]/[EXT PEDAL]of the KEYBOARD ASSIGN Section is lighted (On).
*
Messages for the system or for the entire organ voice will be transmitted on the channel specified
by Control MIDI Channel (SYSTEM MIDI MENU -> Control MIDI Ch.).
*
Messages for the organ upper/lower/pedal part will be transmitted on the each channels specified
by Organ MIDI Channel (SYSTEM MIDI MENU -> Organ MIDI Ch).
*
Messages for the orchestral upper/lower/pedal part will be transmitted on the each channels
specified by Orchestral MIDI Channel (SYSTEM MIDI MENU -> Orch MIDI Ch).
*
Following messages are not transmitted if the "Tx" of Organ Voice & Orchestral Voice MIDI
Transmit/MIDI Receive Switch (SYSTEM MIDI MENU -> Org&Orch MIDI) is Off.
Channel Voice Message
Note Off [ORGAN] [ORCH] [EXT]
Status
2nd byte
8nH
kkH
n =MIDI Channel Number:
kk =note number:
kk =note number:
vv =note off velocity:
Note On [ORGAN] [ORCH] [PEDAL]
Status
2nd byte
9nH
kkH
n =MIDI Channel Number:
kk =note number:
kk =note number:
vv =note on velocity:
Control Change
Bank Select (Controller number 0, 32) [EXT]
Status
2nd byte
BnH
00H
BnH
20H
n =MIDI Channel Number:
mm, ll =Bank number:
*
The bank number will be transmitted for the external upper/lower/pedal part that was designated
by External Tone Select Upper/Lower/Pedal parameter (REGISTRATION MIDI MENU -> Ext
Coarse Tune). (Initial value is "Off.")
Modulation (Controller number 1) [EXT] [ORCH]
Status
2nd byte
BnH
01H
n =MIDI Channel Number:
vv =modulation depth:
*
Not transmitted for the external upper/lower/pedal part, when the External Part Modulation
Switch(REGISTRATION MIDI MENU -> Ext Modulation) is Off.
Volume (Controller number 7) [EXT] [CTRL] [ORCH]
Status
2nd byte
BnH
07H
n =MIDI Channel Number:
vv =volume:
*
The value of the Orchestral Harmonic Bar will be transmitted for the external upper/lower/pedal
part, when the External Part Volume Switch (REGISTRATION MIDI MENU -> Ext Volume) is On.
102
3rd byte
vvH
0H–FH (ch.1–ch.16)
1EH–65H (30–101)
(Organ Voices and Orchestral Voices)
06H–7DH (6–125) (External)
40H (64)
3rd byte
vvH
0H–FH (ch.1–ch.16)
1EH–65H (30–101)
(Organ Voices and Orchestral Voices)
06H–7DH (6–125) (External)
01H–7FH (1–127)
3rd byte
mmH
llH
0H–FH (ch.1–ch.16)
00 00H–7F 7FH (bank.1–bank.16384)
3rd byte
vvH
0H–FH (ch.1–ch.16)
00H–7FH (0–127)
3rd byte
vvH
0H–FH (ch.1–ch.16)
00H–7FH (0–127), Initial value is "64H" (100)
Pan (Controller number 10) [EXT]
Status
2nd byte
BnH
0AH
n =MIDI Channel Number:
vv =pan: 00H–40H–7FH (left–center–right), Initial value is "40H" (center)
Expression (Controller number 11) [EXT] [CTRL] [ORCH]
Status
2nd byte
BnH
0BH
n =MIDI Channel Number:
vv =expression:
*
Not transmitted for the external upper/lower/pedal part, when the External Part Expression
Switch(REGISTRATION MIDI MENU -> Ext Expression) is Off.
General Purpose Controller 1 (Controller number 16) (Orchestral Glide)
[ORCH]
Status
2nd byte
BnH
10H
n =MIDI Channel Number:
vv =control value:
General Purpose Controller 2 (Controller number 17) (Wheel Brake)
[CTRL]
Status
2nd byte
BnH
11H
n =MIDI Channel Number:
vv =control value:
General Purpose Controller 3 (Controller number 18) (Overdrive)
[CTRL]
Status
2nd byte
BnH
12H
n =MIDI Channel Number:
vv =control value:
General Purpose Controller 4 (Controller number 19) (Ring Modulator
Frequency) [CTRL]
Status
2nd byte
BnH
13H
n =MIDI Channel Number:
vv =control value:
Hold 1 (Controller number 64) [EXT] [ORGAN] [ORCH]
Status
2nd byte
BnH
40H
n =MIDI Channel Number:
vv =control value:
*
Not transmitted for the external upper/lower/pedal part, when the External Part Hold Switch
(REGISTRATION MIDI MENU -> Ext Hold) is Off.
Sound Controller 1–9 (Controller number 70–78) [ORGAN]
Status
2nd byte
BnH
ccH
n =MIDI Channel Number:
cc =Controller number:
vv =control value:
*
The Harmonic Bar level will change.
*
The value can be transmitted when Harmonic Bar Mode (SYSTEM MIDI MENU -> Harmon-
icBarMode) is "Mode 2." To change the assignment of control changes to CC#1–31, 33–95, use
H.Bar Controller Number (SYSTEM MIDI MENU ->H.Bar CC No.)
*
With the factory setting, control change message are assigned to each Harmonic Bar as follows.
3rd byte
vvH
0H–FH (ch.1–ch.16)
3rd byte
vvH
0H–FH (ch.1–ch.16)
10H–7FH (16–127)
Initial value is "7FH" (127) (Organ Voices)
00H–7FH (0–127)
Initial value is "7FH" (Orchestral Voices)
3rd byte
vvH
0H–FH (ch.1–ch.16)
00H–7FH (0–127) 0–63 = Off, 64–127 = On
3rd byte
vvH
0H–FH (ch.1–ch.16)
00H–7FH (0–127) 0–63 = SPIN, 64–127 = BRAKE
3rd byte
vvH
0H–FH (ch.1–ch.16)
00H–7FH (0–127)
3rd byte
vvH
0H–FH (ch.1–ch.16)
00H–7FH (0–127)
3rd byte
vvH
0H–FH (ch.1–ch.16)
00H–7FH (0–127) 0–63 = Off, 64–127 = On
3rd byte
vvH
0H–FH (ch.1–ch.16)
46H–4EH (70–78)
00H–7FH (0–127)
Publicidad
Tabla de contenido
