Work Breaks And Transport (See Figure K-L); Maintenance And Service; Maintenance And Cleaning - Bosch PFS 3000-2 Manual Original

Spraying capacity Setting
Not enough material on tar- The spraying capacity must
get area: be increased.
– Turn up by one setting.
Setting the Air Flow (see figure D)
(AIRVolume)
– Set the sliding switch (24) to the appropriate application
to set the correct air flow and pressure for the spray ma-
terial used.
Off "Wood" application
Thin-viscosity spray
material
Dampening Wallpaper
To make it easier to remove old wallpaper, you can spray
warm water on the wallpaper (max. 55 °C). Use the grey
nozzle cap (10) to do so.
Work breaks and transport (see figure K–L)
A carrying handle (22) and a carrying strap (21) are fitted to
the base unit to enable easy transport of the fine-spray sys-
tem.
You can hang the base unit (20) across your shoulder during
work using the carrying strap (21).
The spray gun (1)can be put down on a flat work surface dur-
ing breaks. No spray material can leak out.
Always put the spray gun upright on a flat surface
u
when it is filled with spray material. Spray material can
leak out from a spray gun if it is lying down.

Maintenance and Service

Maintenance and Cleaning

Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
Thoroughly clean the individual parts of the fine-spray
u
system after each use, especially all paint-carrying
components. Proper cleaning is a prerequisite for fault-
less and safe operation of the spray gun. No warranty
claims will be accepted if cleaning has not been done at
all or has not been done properly.
Bosch Power Tools
Cleaning the fine spraying system (see figure M)
Always clean the spray gun and the container with the re-
spective diluting agent (paint thinner or water) for the spray
material being used.
Never clean the nozzle and air holes in the spray gun with
pointed objects.
– Switch the base unit (20) off.
– Remove the air hose (18) both from the base unit (20)
and from the spray gun (1)(quarter turn of the bayonet
lock (19) anticlockwise; pull the bayonet lock (19) out of
the port (8)/(28)).
– Clean the base unit if necessary with a cloth moistened
with diluting agent and then remove the base unit (20)
and the air hose (18) from the immediate cleaning envir-
"Wall" application
onment.
– Press the trigger switch (5) on the spray gun so that the
spray material can flow back into the container.
– Unscrew the container (7) and empty the remaining
Thick-viscosity spray
spray material back into the original spray material.
material
– Fill the container (7) halfway with the diluting agent
(solvent or water) and fit it to the spray gun (1)again.
– Shake the spray gun several times.
– Unscrew the container (7) and empty the container com-
pletely into an empty material tin.
– Remove the cap nut (3), the air cap (2), the nozzle cap
used (9)/(10) and the suction tube (15) with the con-
tainer seal (14).
– Clean all paint-carrying parts in a bucket with diluting
agent using the cleaning brush (26) or with a commer-
cially available washing-up brush. Also clean the paint
channel (17) of the spray gun (1).
– Check that the suction tube (15) and the container
seal (14) are free of spray material and undamaged.
If required, clean the container seal (14) again with dilut-
ing agent.
– Clean the ventilation hole (16) using the cleaning
brush (26).
– If required, clean the filling sieve (11) thoroughly with di-
luting agent.
– Clean the outside of the container and the spray gun with
a cloth moistened in paint thinner.
– Before mounting, allow all components to dry thoroughly.
– Reassemble the fine-spray system in reverse order.
Slide the container seal (14) upwards again into the
groove of the suction tube (15).
Ensure that the container seal is positioned precisely all
around in the suction tube groove in order to seal the
spray gun correctly.
Make sure that you slide the suction tube (15) all the way
back onto the paint channel (17).
Cleaning the air filter (see figure N)
The air filter (30) must be cleaned occasionally. The air filter
must be replaced if it is heavily soiled.
– Open the air filter cover (25).
– Remove the air filter (30).
English | 23
1 609 92A 58D | (28.10.2019)