Technical Data - Steinbach Speed Clean Classic 250N Manual De Instrucciones

Operation with a pool vacuum cleaner (Illustration 9)
■ The pool vacuum cleaner's hose can be connected directly to the filter
system's suction pipe. In doing so, the pool vacuum cleaner's hose must be
completely filled with water.
■ The use of a skimmer with a strainer basket is recommended for filter systems
without pre-filters.
■ Please observe the pool vacuum cleaner's operating instructions. To prevent
the filter from running dry and thus overheating, no air should be allowed to
enter the filter system.
■ Please select the "FILTERN" position on the valve head.
■ Alternatively, you can also select the "ENTLEEREN (empty)" position, for
example if algae forms in the pool. Dirty pool water will not then run back
into the pool, but will be directly channelled away via the waste pipe. When
selecting this setting, it is necessary to re-fill your pool to the correct level after
cleaning, if necessary.

Technical data:

040385 Classic 250
■ Circulation power 3,800 l/h
■ Pump is not self-priming
■ maximum water temperature 35 °C
■ 230 V / 200 W
■ 7 way valve with pressure gauge
■ Tank Ø 250 mm
■ Connector Ø 32/38 mm
■ Base plate
■ requires approx. 10 kg sand
■ recommended grain size 0.7 - 1.2 mm
■ for pools up to 19,000 l capacity
■ Optional: Speedpart Container for UV system Speed UV
040310 Classic 310
■ Circulation power 4,500 l/h
■ Self-priming pump with pre-filter
■ Maximum water temperature 35 °C
■ 230 V / 250W
■ 7 way valve with pressure gauge
■ Tank Ø 320 mm
■ Connector Ø 32/38 mm
■ Base plate
■ Requires approx. 20 kg sand
■ Recommended grain size 0.7-1.2 mm
■ For pools up to 22,000 l capacity
■ Optional: Speedpart Container for UV system Speed UV
040340 Classic 400
■ Circulation power 6,600 l/h
■ Self-priming pump with pre-filter
■ Maximum water temperature 35 °C
■ 230 V / 450W
■ 7 way valve with pressure gauge
■ Tank Ø 370 mm
■ Connector Ø 32/38 mm
■ Base plate
■ Requires approx. 25 kg sand
■ Recommended grain size 0.7-1.2 mm
■ For pools up to 33,000 l capacity
■ Optional: Speedpart Container for UV system Speed UV
Changing the filter sand
The filter sand should be
depending on how much
changed every 2-3 years,
the filter system is operated.
250N/310/400_040385_040310_040340_v1901
Care instructions
Visible impurities are removed via the filter system. However, this does
not apply to algae, bacteria and other micro-organisms, which are also
a constant threat to clear, clean and healthy swimming pool water. For
their prevention or removal special water care products are available,
which when dosed correctly and regularly do not cause any irritation
for bathers and guarantee hygienically perfect water for swimming.
Cleaning
Turn the filter system off before
plug. Use conventional cleaning products. Do not use solvent based
or abrasive cleaning agents, i.e.
Storage
The product must be thoroughly
which, it is to be stored in
Disposal
Disposing of packaging: The packaging material has been selected in
view of environmental concerns and disposability and is therefore recyclable.
The paper and cardboard can be recycled, as can the plastic coverings.
Disposing of the product: Applicable
other European states with systems
sorting recyclable materials. Dispose
with any laws and regulations applicable at your place of residence.
Warranty conditions
The respective country's legal provisions for warranty conditions shall apply
accordingly. For Austria and Germany, these apply for 2 years after the date of invoice.
EN
cleaning and pull out the mains
no hard sponges, brushes
dried after cleaning. After
a dry location protected from frost.
in the European Union
in place for collecting
of the product in accordance
etc..
and
and
9