Preparation; Remote Control; Filling With Water; Electrical Connection - ProfiCare PC-LB 3077 Manual De Instrucciones

• We recommend that you use distilled or freshly boiled
and cooled water.
• The water may not exceed a temperature of 40 °C.
• Replace the water every 3 - 4 days, even if it is not used
up.
• If you do not use the appliance for longer periods of
time, remove the water from the tank and from the base
appliance. Allow the parts to dry.

Preparation

Remote Control

NOTE:
The button cell in the battery compartment of the remote
control has been secured with a foil for transport. This
will extend the durability of the battery. Before initial use
please remove this foil so that the remote control is ready
for operation.
The remote control has a range of approx. 8 meters. When
using the remote control, please ensure that there are no ob-
stacles placed between it and the sensor on the appliance.
Changing the Battery of the Remote Control
If the range of the remote control is reduced during use,
please proceed as follows:
1. Open the battery compartment on the bottom of the
remote control by holding the lever inwards and pulling
out the battery compartment.
2. Replace the button cell with a battery of the same type
(CR2025). Ensure correct polarity.
3. Then close the battery lid.

Filling with Water

CAUTION:
Do not pour any water into the opening of the nozzle.
1. Remove the lid to pour in water. Use the handle to
remove the water tank from the base unit. Turn the water
tank over. The filler hole is located underneath the tank.
2. Twist off the filler cap in the direction
into the tank up to approx. 3 centimetres below the rim.
3. Close the filler cap again by twisting it in the
and put the tank back into the base appliance. Observe
the markings on the right side of the water tank and the
base unit. These must be aligned with each other.
4. Place the lid with the steam nozzle on the water tank.
NOTE:
During operation, always put on the lid with the steam
nozzle, otherwise moisture will settle on the appliance.

Electrical Connection

1. Before connecting the plug to a wall socket, verify the
correct mains voltage. Refer to the specifications on the
rating label of the appliance.
PC-LB3077_IM
2. Insert the plug in a duly installed protective contact
socket. You will hear a short beep.
• The buttons are to be found both on the appliance itself
and on the remote control. Buttons with the same symbol
have the same function.
• The buttons on the appliance are sensor touch buttons.
In order to perform the corresponding function gently
touch the buttons. Whenever a button is pressed, it will
be confirmed by a beep sound.
• The buttons
functional buttons. In order to use the different functions,
the corresponding button must either be pressed briefly,
or be pressed for about 3 seconds.
NOTE:
Operation is explained by the buttons on the remote
control.

Switching the Appliance On / Off

• Press the
The appliance always starts operating in level 3.
Steam generated at the steam outlet will be transported
to the steam nozzle by fan operation. The display shows
the current humidity (HUMID) and temperature (TEMP)
alternately.
• Press the
appliance.

Set Fog / Steam Level

You can select 3 different steam settings – from low to
high. Press the MIST LEVEL button to select a level. The
selected level (1, 2 or 3) is shown in the display.

Set Humidity

Press the
midity between 45 % and 80 %. You can adjust the humidity
in 5 % steps.
. Fill the water
NOTE:
• The set air humidity flashes for approx. 3 seconds in
direction
the display. After that, the display alternately shows
you the current humidity and temperature.
• Once the preset setting has been reached, the
appliance will turn off and then control the humidity
automatically.

Ionizing Function

Negative ions support the well-being of humans. They
can, for example, help with the dissipation of electrostatic
charges.
• Press the
bol
• Press the

Operation

and on the appliance are also multi-
POWER button to switch on the appliance.
POWER button again to switch off the
HUMIDITY button repeatedly, to select a hu-
ION button to activate ionization. The sym-
appears in the display.
ION button again, to turn off the function.
43
26.09.19