Phonic i2600 Manual Del Usuario página 16

11.1e. If selected a Hi-Pass_Q (variable Q High Pass) filter,
then the filter can be set by the following parameters
Out-[x] EQ-[x] (up to 5 filters available)
[Freq] [Gain] [Q]
-> 1000Hz ----- Q=1.00
11.1f. If selected an All-Pass_2 (second order, variable Q All Pass) filter,
then the filter can be set by the following parameters
Out-[x] EQ-[x] (up to 5 filters available)
[Freq] [Gain] [Q]
-> 1000Hz ----- Q=1.00
12. Output[x] [Name] Vu-Meter
Vu-Meter = Level
-> Vu-Meter = Level
Utility Menu
From the Default Screen it is possible access the UTILITY menu
pushing the UTILITY button. The Sub Menu pages can be selected
by simply rotating the NAV/PM1 encoder clockwise and counter
clockwise. Select a sub menu page by using the ENTER button.
The next menu is scrollable using the NAV/PM1 encoder and once
again accessed by pushing the ENTER button.
Through the ESC button it is possible to go back to the preceding
menu at any time. Once inside the Sub Menus pages the several
options can be scrolled and using the PM2 or PM3 encoders and
selected/confirmed pushing the ENTER button.
Note: In every Sub Menu the option currently selected will have
an asterisk ("*") to the right of the description on the LCD screen.
Options that are not selected running will be displayed with no
asterisk. Pushing the ENTER button on an unselected option will
mean an asterisk will then appear and this option will take over as
the currently selected option.
System Utilities Submenu
This sub menu allows to access several operations related to the
i2600 Start Up and General Configuration. Within the System
Utilities submenu, the following settings are adjustable:
Input Mode Setup – this page allows the selection of the operating
mode of the i2600. There are two options to select from:
Stereo Mode: In this operating mode the i2600 is considering
the all processes available before the X Over as applied to a
Stereo Input Signal. In this mode all parameter adjustments
made for the all processes are applied in the same way on
both channels. In other words, input channels 1 and 2 are
working in link mode.
Input Mode Setup
Setup : Stereo
12
20kHz
[Freq.] 20Hz
[Amp.]
:
20kHz
[Freq.] 20Hz
[Amp.]
:
20kHz
PM1 N/A Level
Limiter Act.
RMS Cmp Act.
Dual Mono Mode: In this operating mode the i2600 is
considering the all processes available before the X Over
as applied to separate channels. This being the case, all
parameter adjustments made for the all processes are applied
in different ways to the 2 independent Input channels. In this
instance, input channels 1 and 2 are not working in link mode.
Power On Procedure – this gives you the ability to select the
options that will apply when the i2600 powers up after being
switched on. By pressing ENTER and rotating the PM2 or PM3
encoder it is possible to choose between two options: "Fade In
On" or "Fade In Off".
Fade In Off: When the i2600 is turned on all outputs will be
MUTED or UNMUTED automatically depending on their status
before the unit was switched off.
Fade In On: When the i2600 is turned on, all outputs will be
automatically MUTED regardless of their status before the unit
was turned off. All previously active outputs will then fade in
gradually to avoid any sudden sounds being sent through any
external devices.
Delay Time/Distance – this page allows you to select the
measurement unit to be used for Delay Time, whether it's time
(milliseconds or "ms") or distance (meters or "m"). By pressing
ENTER and rotating the PM2 or PM3 encoder it is possible to
select the measurement unit to be used for the delay. Push the
ENTER button to confirm.
Unit : Distance ( M )
*
Software Version – this option will allow users to view their
currently installed software version.
-----
-----
[Q]
:
----- 20.00
-----
[Q]
:
----- 20.00
Same as PM2
Input Mode Setup
Setup : Dual Mono
Delay Units
20.00
0.30
:
0.30
:
*
*
i2600