Work; Scrubbing With Drying; Scrubbing Without Drying; Drying - Hillyard Trident R26SC Pro Manual De Uso

The machine can be used in the following work modes:
• ECO-MODE, read the section "ECO-MODE";
• MANUAL MODE, read the section "MANUAL
• PROGRAM ZONE, read the section "PROGRAM ZONE
As an example, we will look at the program mode. To begin working in this mode, proceed as follows:
1. Make all the checks listed in "PREPARING TO
2. Sit on the driver's seat.
3. Insert the key (1) into the main switch on the control panel. Set the main switch to "I" (Fig.1).
4. Select the desired work area, press one of the three "ZONE" buttons (2) on the control panel (read paragraph
5. Open the detergent solution passage in the machine water system, move the knob (3) upwards (Fig.3).
6. Press the drive pedal (4) to begin moving the machine (Fig.4).
1 2
1
2
The squeegee and brush head lower until they touch the floor, as soon as the drive pedal is pressed, the traction motor, brush head motor and suction motor will start working. As a result, the solenoid valve will
also be activated and detergent solution will be dispensed onto the brushes. During the first few metres, check that there is sufficient solution and that the squeegee is drying correctly.
The machine will now begin to work with full efficiency until the battery is flat or until the detergent solution has finished.

SCRUBBING WITH DRYING

To perform a scrubbing and drying program, proceed as follows:
1. Make all the checks listed in "PREPARING TO
2. Sit on the driver's seat.
3. Move the main switch (1) to position "I" and turn the key a quarter turn clockwise (Fig.1).
4. Lower the brush head body and press the "BRUSH HEAD CONTROL" button (2) on the control panel (Fig.2).
N.B. : as soon as the button (2) on the control panel is pressed, the green LED (3) ("BRUSH HEAD BODY WORK POSITION") will switch on (Fig.2).
5. Lower the squeegee body and press the "SQUEEGEE CONTROL" button (4) on the control panel (Fig.2).
N.B. : as soon as the button (4) on the control panel is pressed, the green LED (5) ("SQUEEGEE BODY WORK POSITION") will switch on (Fig.2).
6. Press the drive pedal (6) to begin moving the machine (Fig.3).
N.B.: Once the drive pedal has been pressed, the brush head body will begin to descend into its working position.
N.B.: the gearmotor will only begin functioning, and the solenoid valve will only begin dispensing detergent solution, when the brush head body is in its working position.
5
1
4
1
2

SCRUBBING WITHOUT DRYING

To perform a scrubbing program without drying , proceed as follows:
1. Make all the checks listed in "PREPARING TO
2. Sit on the driver's seat.
3. Move the main switch (1) to position "I" and turn the key a quarter turn clockwise (Fig.1).
4. Lower the brush head body and press the "BRUSH HEAD CONTROL" button (2) on the control panel (Fig.2).
N.B. : as soon as the button (2) on the control panel is pressed, the green LED (3) ("BRUSH HEAD BODY WORK POSITION") will switch on (Fig.2).
5. Press the drive pedal (4) to begin moving the machine (Fig. 3).
N.B.: Once the drive pedal has been pressed, the brush head body will begin to descend into its working position.
N.B.: the gearmotor will only begin functioning, and the solenoid valve will only begin dispensing detergent solution, when the brush head body is in its working position.
1
1
2

DRYING

To perform a drying only program, proceed as follows:
1. Make all the checks listed in "PREPARING TO
2. Sit on the driver's seat.
3. Move the main switch (1) to position "I" and turn the key a quarter turn clockwise (Fig.1).
4. Lower the squeegee body and press the "SQUEEGEE CONTROL" button (2) on the control panel (Fig.2).
N.B. : as soon as the button (2) on the control panel is pressed, the green LED (3) ("SQUEEGEE BODY WORK POSITION") will switch on (Fig.2).
Press the drive pedal (4) to begin moving the machine (Fig. 3).
5.

WORK

MODE",
MODE".
WORK".
3
3
WORK".
3
2
3
WORK".
3
2
3
WORK".
"PROGRAM ZONE MODE") (Fig.2).
4
4
6
4
16