Emptying The Solution Tank; Cleaning The Vacuum Tube; Cleaning The Water System Filter - Hillyard Trident R26SC Pro Manual De Uso

EMPTYING THE SOLUTION TANK

Proceed as follows to empty the solution tank:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled
CAUTION: users are advised to always wear protective gloves, to avoid the risk of serious injury to hands.
3. Close the tap's output flow, and shift the knob (1) on the left hand side of the steering column (Fig.1) downward.
4. Remove the detergent solution filter cap (2) (Fig.2).
5. Open the tap's output flow, and shift the knob (1) on the left hand side of the steering column upward.
N.B.: the place designated for this operation must comply with current environmental protection regulations.
6. When the solution tank is empty, repeat the operations in the reverse order to reassemble all the parts.
2
1
1

CLEANING THE WATER SYSTEM FILTER

In order to clean the water system's filter, do the following:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled
CAUTION: users are advised to always wear protective gloves, to avoid the risk of serious injury to hands.
3. Close the tap's output flow, and shift the knob (1) on the left hand side of the steering column (Fig.1) downward.
4. Remove the detergent solution filter cap (2) (Fig.2).
5. Rinse the filter cartridge under a jet of water, and use a brush to eliminate any impurities, if necessary.
N.B.: the place designated for this operation must comply with current environmental protection regulations.
6. Once the filter cartridge is clean, repeat the operations in the opposite order to reassemble all the parts.
2
1
1

CLEANING THE VACUUM TUBE

Careful cleaning of the vacuum hose guarantees better cleaning of the floor as well as a longer suction motor life. Proceed as follows to clean the vacuum hose:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled
ATTENTION: users are advised to always wear protective gloves, to avoid the risk of serious injury to hands.
3. Extract the vacuum tube (1) from the vacuum nozzle on the squeegee body (Fig.1).
4. Remove the vacuum tube (1) via the hole on the back of the recovery tank (Fig.2).
1 1
1 2
5. The vacuum hose from the retainers present inside the recovery tank.
6. Rinse the inside of the vacuum hose with a jet of running water.
7. Repeat the operations in reverse order to reassemble all the parts.
To clean the vacuum tube with the spray gun kit, proceed as follows:
1. Take the machine to the maintenance area.
2. Lift the brush head body and press the "BRUSH HEAD CONTROL" button (1) on the control panel (Fig.1).
N.B. : as soon as the button (1) on the control panel is pressed, the green LED (2) ("BRUSH HEAD BODY WORK POSITION") will switch off (Fig.1).
3. Lift the squeegee body and press the "SQUEEGEE CONTROL" button (3) on the control panel (Fig.1).
N.B. : as soon as the button (3) on the control panel is pressed, the green LED (4) ("SQUEEGEE BODY WORK POSITION") will switch off (Fig.1).
4. Stand at the back of the machine.
CAUTION: users are advised to always wear protective gloves, to avoid the risk of serious injury to hands.
N.B.: the place designated for this operation must comply with current environmental protection regulations.
5. Extract the vacuum tube (5) from the vacuum nozzle on the squeegee body (Fig.2).
6. Remove the vacuum tube (5) via the hole on the back of the recovery tank (Fig.3).
CAUTION: users are advised to always wear protective gloves, to avoid the risk of serious injury to hands.
"SECURING THE MACHINE").
2
"SECURING THE MACHINE").
2
"SECURING THE MACHINE").
24