Troubleshooting - Rotel RSX-1562 Manual De Instrucciones

48
E Q V A L U E
S P E A K E R A L L S P E A K E R
:
- - - - - - - - 1 - - - - 2 - - - - 3 - - - - - 4 - - - - - 5 -
F r e q : 4 0 6 0
Q : 2 2
G a i n : 0 0
- - - - - - - - 6 - - - - 7 - - - - 8 - - - - - 9 - - - - 1 0 -
F r e q : 1 3 0 0 1 7 5 0
Q : 2 2
G a i n : 0 0
E Q S E T U P M E N U
BAND 1 Freq : 20Hz - 80Hz, 1Hz Step
BAND 2 Freq: 20Hz - 80Hz, 1Hz Step
BAND 3 Freq: 81Hz - 140Hz, 1Hz Step
BAND 4 Freq: 81Hz - 140Hz, 1Hz Step
BAND 5 Freq: 141Hz - 200Hz, 1Hz Step
BAND 6 Freq: 1110Hz - 1550 Hz, 10Hz Step
BAND 7 Freq: 1560Hz - 2000 Hz, 10Hz Step
BAND 8 Freq: 2.1kHz - 8kHz, 100Hz Step
BAND 9 Freq: 8.1kHz - 14kHz, 100Hz Step
BAND 10 Freq: 14.1kHz - 20kHz, 100Hz Step
Q : 1 - 24
Gain : -12dB - 0 - +3dB
Note: Q in EQ value relates to the bandwidth of the filter. The higher
the value, the narrower the bandwidth.

Troubleshooting

Most difficulties in audio systems are the result of incorrect connections,
or improper control settings. If you encounter problems, isolate the area
of the difficulty, check the control settings, determine the cause of the fault
and make the necessary changes. If you are unable to get sound from
the unit, refer to the suggestions for the following conditions:
The unit does not turn on
• Make sure the power cord is plugged into the rear panel and a
AC outlet.
• Make sure the rear panel POWER switch is in the ON position.
No sound from any input
• Make sure that MUTING is off and VOLUME is turned up.
• Make sure that preamp outputs are connected to a power amplifier
and that the amplifier is turned on.
• Make sure source inputs are connected and configured correctly.
• Check that the setting for HDMI AUDIO in the VIDEO/HDMI on-
screen menu is AMP MODE.
No sound from digital sources
• Make sure that digital input connector is assigned to the proper
source input and that the source input is configured to use the digital
input rather than an analog input.
• Check the configuration of the DVD player to ensure that the bitstream
and/or DTS digital output is activated.
S E T
1 0 0 1 2 0 1 6 0
2 2 2
0 0 0
4 K 1 0 K 1 6 K
2 2 2
0 0 0
Default 40 Hz
Default 60 Hz
Default 100 Hz
Default 120 Hz
Default 160 Hz
Default 1300 Hz
Default 1750 Hz
Default 4k Hz
Default 10k Hz
Default 16k Hz
RSX-1562 SURROUND SOUND RECEIVER
No sound from some speakers
• Check all power amp and speaker connections.
• Check Speaker Configuration settings in the Setup menus.
No video output on TV monitor.
• Make sure that the TV monitor is connected properly and check the
input assignments. Composite Video TV monitors can only be used
with interlaced SD sources. HDMI and Component TV monitors can
be used with Standard Definition (SD) and High Definition (HD)
sources. An HDMI 1080p source can only be sent to a 1080p-
compliant TV monitor .
• Component Video output at 720p or 1080i may not be available
if the source signal includes HDCP copy protection.
• HDMI cables must be 5 meters or less in length.
• If watching 3D source, make sure the display is 3D enabled.
Video and Audio do not match.
• Check that the proper video source is selected for each input.
• Check that the group delay (lip-synch) setting is not mis-adjusted.
Clicking or popping sounds when switching inputs
• The unit uses relay switching to preserve maximum sound quality.
The mechanical clicking of the relays is normal.
• During switching, it may take a split second for digital signals to
be recognized and properly decoded. Rapid repeated switching
between inputs or settings can result in clicks or pops from the
speakers as the unit attempts to lock on to the rapidly changing
signals. This causes no harm.
• Switching between HDMI sources may cause delays as HDMI two
way communications "handshake" must be established between the
source and display. The time required for the handshake varies
from equipment.
Controls do not operate
• Make sure that fresh batteries are installed in the remote.
• Make sure that the IR sensor on the front panel is not blocked. Aim
the remote at the sensor.
• Make sure the sensor is not receiving strong IR light (sunlight,
halogen lighting, etc.)
• Unplug the unit from the AC outlet, wait 30 seconds, and plug it
back to reset.
No video from ZONE 2, 3 or 4
• Check ZONE SETUP configuration and ZONE video input setting
assigned and make sure that a video source is connected.