Tabla De Condiciones De Entrada / Salida - Hypertherm HyDefinition HD4070 Manual Del Operador

APÉNDICE D – TABLA DE CONDICIÓN DE LA PANTALLA DE SERVICIO (#18)
La información que sigue es para búsqueda de averías por los técnicos de servicio. Si la terminología usada no es
conocida por el técnico, él debe ponerse en contacto con la Organización Europea de Apoyo Técnico, 800 49 73
7843 E-mail; Servicio Técnico en EE. UU., 800-643-9878 (service@hypertherm.com); o Hypertherm Brasil Ltda.,
55 21 2278 6162 (HTBrasil.info@hypertherm.com).

Tabla de condiciones de Entrada / Salida

Port 0 Base Addr 224H
Bit 0 Select 160 amp
Bit 1 Select 80 amp
Bit 2 Select 40 amp
Bit 3 Select 20 amp
Bit 4 Select 10 amp
Select 1_10 current/ cable
Bit 5
checkCout
Bit 6 Fan control
Bit 7 Contactor control
Port 3 Base Addr 220H
Bit 0 Slave Chopper #1 temp OK Pin 47
Bit 1 Slave Chopper #2 temp OK Pin 45
Bit 2 Slave_Temp_Airflow_OK
Bit 3 Slave current OK
Bit 4 Spare input
Bit 5 Transfer sense
Bit 6 Coolant flow switch
Bit 7 Coolant temp switch
Port 6 Base Addr 50H
Bit 0 Spare_out14
Bit 1 Spare_out15
Bit 2 Spare_out16
Bit 3 Spare_out17
Bit 4 Spare_out7
Bit 5 Spare_out8
Bit 6 Spare_out20
Bit 7 Spare_out21
Port 9 Base Addr 200H
Bit 0 Transfer 2
Bit 1 Transfer 3
Bit 2 Select 5 amp
Bit 3 Select 2 amp
Bit 4 Watchdog_out
Bit 5 Slave 5 amp select
Bit 6 Slave 2 amp select
Bit 7 Cable_checkB_out
Port 12 Base Addr 204H
Bit 0 THC1 Retract complete
Bit 1 THC1 Cable install
Bit 2 THC1 Discrete error
Bit 3 THC2 Retract complete
Bit 4 THC2 Cable installed
Bit 5 THC2 Discrete error
Bit 6 THC2 IHS complete
Bit 7 CNC system start
Serial Channels
Com 1 Debug port
Com 2 Display serial
Com 3 CNC Serial
Com 4 THC1/THC2 switched serial 02E8H
d-2
0
Output Port 1 Base Addr 225H
Pin 47 Bit 0 Input power active
Pin 45 Bit 1 Missing phase detect
Pin 43 Bit 2 Chopper #1 temp OK
Pin 41 Bit 3 Chopper #2 temp OK
Pin 39 Bit 4 Temp_Airflow_OK
Pin 37 Bit 5 Output current OK
Pin 35 Bit 6 Slave input power active
Pin 33 Bit 7 Slave missing phase detect Pin 17
Input Port 4 Base Addr 221H
Bit 0 Slave contactor control
Bit 1 Slave DC output On/Off
Pin 43 Bit 2 Pump control
Pin 41 Bit 3 Torch #1 coolant
Pin 39 Bit 4 Torch #2 coolant
Pin 37 Bit 5 Spare out
Pin 35 Bit 6 Transfer 1
Pin 33 Bit 7 Spare_out2
Ouput Port 7 Base Addr 51H
Pin 47 Bit 0 Spare_in1
Pin 45 Bit 1 Spare_in2
Pin 43 Bit 2 Spare_in3
Pin 41 Bit 3 Spare_in6
Pin 39 Bit 4 Spare_in7
Pin 37 Bit 5 Spare_in8
Pin 35 Bit 6 Spare_in9
Pin 33 Bit 7 Spare_in10
Output Port 10 Base Addr 201H
Pin 47 Bit 0 Pilot arc relay
Pin 45 Bit 1 Surge injection select
Pin 43 Bit 2 Spare_out13
Pin 41 Bit 3 THC1 cycle start
Pin 39 Bit 4 THC2 cycle start
Pin 37 Bit 5 Analog6_check_out
Pin 35 Bit 6 Cable_checkA_out
Pin 33 Bit 7 Spare_out18
Input Port 13 Base Addr 205H
Pin 47 Bit 0 CNC corner hold
Pin 45 Bit 1 CNC plasma sync
Pin 43 Bit 2 CNC emergency stop
Pin 41 Bit 3 CNC machine cable installedPin 25
Pin 39 Bit 4 CNC spare input
Pin 37 Bit 5 Watchdog_interlock
Pin 35 Bit 6 THC1 IHS complete
Pin 33 Bit 7 Cable_checkB_in
Addr 100H Analog Inputs
03F8H Channel Total current
02F8H Channel Power Check
03E8H Channel Not used
Channel Not used
Channel Not used
Channel Not used
Channel Analog6_check_in
Channel Not used
Input Port 2 Base Addr 226H
Pin 31 Bit 0 DC output On/Off
Pin 29 Bit 1 Slave 160 amp select
Pin 27 Bit 2 Slave 80 amp select
Pin 25 Bit 3 Slave 40 amp select
Pin 23 Bit 4 Slave 20 amp select
Pin 21 Bit 5 Slave 10 amp select
Pin 19 Bit 6 Slave 1_10 current
Bit 7 Slave fan control
Output Port 5 Base Addr 222H
Pin 31 Bit 0 Plasma interface spare input Pin 15
Pin 29 Bit 1 Master_door_interlock
Pin 27 Bit 2 Cable_checkA_in
Pin 25 Bit 3 Slave_door_interlock
Pin 23 Bit 4 Cable_checkC_in
Pin 21 Bit 5 Gas_error
Pin 19 Bit 6 Spare_in4
Pin 17 Bit 7 Spare_in19
Input Port 8 Base Addr 52H
Pin 31 Bit 0 Spare_in11
Pin 29 Bit 1 Spare_in12
Pin 27 Bit 2 Spare_in13
Pin 25 Bit 3 Spare_in14
Pin 23 Bit 4 Spare_in15
Pin 21 Bit 5 Spare_in16
Pin 19 Bit 6 Spare_in17
Pin 17 Bit 7 Spare_in18
Output Port 11 Base Addr 202H
Pin 31 Bit 0 Gas_state1
Pin 29 Bit 1 Gas_state2
Pin 27 Bit 2 Gas_state3
Pin 25 Bit 3 Spare_out19
Pin 23 Bit 4 CNC_transfer
Pin 21 Bit 5 CNC_motion
Pin 19 Bit 6 THC1_corner_hold
Pin 17 Bit 7 THC2_corner_hold
Input Port 14 Base Addr 206H
Pin 31 Bit 0 CNC ready to fire
Pin 29 Bit 1 CNC arc transfer
Pin 27 Bit 2 CNC machine motion
Bit 3 CNC retract complete
Pin 23 Bit 4 CNC spare output
Pin 21 Bit 5 CNC system error
Pin 19 Bit 6 Serial Select1
Pin 17 Bit 7 Serial Select2
Input
Pin 1
Pin 2
Pin 3
Pin 4
Pin 7
Pin 8
Pin 11
Pin 12
HD4070 Manual del operador
Output
Pin 15
Pin 13
Pin 11
Pin 9
Pin 7
Pin 5
Pin 3
Pin 1
Input
Pin 13
Pin 11
Pin 9
Pin 7
Pin 5
Pin 3
Pin 1
Input
Pin 15
Pin 13
Pin 11
Pin 9
Pin 7
Pin 5
Pin 3
Pin 1
Output
Pin 15
Pin 13
Pin 11
Pin 9
Pin 7
Pin 5
Pin 3
Pin 1
Output
Pin 15
Pin 13
Pin 11
Pin 9
Pin 7
Pin 5
Pin 3
Pin 1