Black and Decker CD455 Manual De Instrucciones página 11

f All toys, washable furniture and utensils used by
children should be washed thoroughly before being
used again.
FEATURES (Fig. A)
1. On/off switch
2. Dust extraction outlet
3. Sanding base
4. Paper clamp lever
5. Hole Punch
ASSEMBLY
Warning! To prevent accidental operation, turn off and
unplug tool before performing the following operations.
Failure to do this could result in serious personal injury.
Fitting sanding sheets (Fig. B)
Note: Never use the tool without a sanding sheet or
accessory in place.
f Soften the sanding sheet by rubbing its non-abrasive
side over the edge of a work top.
f Press the paper clamp levers (4) upwards to release
them from the retaining grooves and open the paper
clamps by pressing them down.
f Place the sheet onto the sanding base, making sure
that the holes in the sheet (if applicable) line up with
the holes in the base.
f Insert the edge of the sanding sheet into the front
paper clamp as shown.
f Press the front paper clamp lever (4) up and locate
it in the retaining groove.
f While keeping a slight tension on the sheet, insert
the rear edge of the sheet into the rear paper clamp.
f Press the rear paper clamp lever (4) up and locate
it in the retaining groove.
Connecting a vacuum cleaner (Fig. C)
f Insert the adaptor (5) into the dust extraction outlet (2).
f Connect the hose (6) of the vacuum cleaner
(not included) to the adaptor.
OPERATION
Switching on and off (Fig. D)
f To switch the tool on, press the front part (I) of
the On/Off switch (1).
f To switch the tool off, press the rear part (O) of the
On/Off switch (1).
HINTS FOR OPTIMUM USE
f Always hold the tool with two hands as shown
in Fig E.
f Do not exert too much pressure on the tool.
f Regularly check the condition of the sanding sheet.
Replace when necessary.
f Always sand with the grain of the wood.
f Always start your sander before it is in contact with
the workpiece and do not switch it off until after it has
been lifted from the workpiece.
f Where possible, clamp the workpiece to a work bench
or similar sturdy surface.
f When sanding new layers of paint before applying
another layer, use extra fine grit.
f On very uneven surfaces, or when removing layers
of paint, start with a coarse grit.
f On other surfaces, start with a medium grit. In both
cases, gradually change to a fine grit for a smooth finish.
DUST COLLECTION
Warning! Fire hazard. Collected sanding dust from
sanding surface coatings (polyurethane, linseed oil, etc.)
can self-ignite and cause fire. To reduce risk, strictly follow
sander manual and coating manufacturer's instructions.
Warning! Fire hazard. When sanding wood that could
contain nails or when sanding metal surfaces, do not use
a vacuum cleaner because sparks are generated. Use
safety glasses and a dust mask. Due to the danger of fire,
do not use your sander to sand magnesium surfaces. Do
not use for wet sanding.
MAINTENANCE
Never apply excessive force when you use your sander.
Too much force can result in an overload and cause
damage to the motor or the workpiece. Always keep the
air cooling vents clear. To clean your finishing sander,
proceed as follows:
Warning! To prevent accidental operation, turn off and
unplug sander before performing the following operations.
Failure to do this could result in serious personal injury.
f Use a clean dry paint brush to clear vents and ducts.
f Clean the housings using a clean damp cloth
(do not use solvents, gas or turpentine.)
Important! To assure product Safety and Reliability,
repairs, maintenance and adjustment should be performed
by authorized service centers or other qualified service
personnel, always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory for your tool, please cal contact your nearest
Service Center.
Warning! The use of any other accessory not
recommended for use with this tool could be hazardous.
ENGLISH • 11