BFT Q.BO PAD Instrucciones De Uso Y De Instalacion página 9

Thank you for buying this product, our company is
sure that you will be more than satisfied with the
product's performance. The product is supplied with
a "Warnings" leaflet and an "Instruction booklet".
These should both be read carefully as they provide
important information about safety, installation, opera-
tion and maintenance. This product complies with the
recognised technical standards and safety regulations.
We declare that this product is in conformity with the
following European Directives: 2004/108/EEC and
2006/95/EEC (and subsequent amendments).
GENERAL SAFETY
WARNING! An incorrect installation or improper
use of the product can cause damage to persons,
animals or things.
• Installation m ust be carried out by qualified person-
nel (professional installer, according to EN 12635),
in compliance with Good Practice and current code.
• Before installing the product, make all structural
changes required to produce safety gaps and to
provide protection from or isolate all crushing, she-
aring and dragging hazard areas and danger zones
in general in accordance with the provisions of stan-
dards EN 12604 and 12453 or any local installation
standards. Check that the existing structure meets
the necessary strength and stability requirements.
• Scrap packing materials (plastic, cardboard,
polystyrene etc) according to the provisions set out
by current standards. Keep nylon or polystyrene
bags out of children's reach.
• Keep the instructions together with the technical
brochure for future reference.
• This product was exclusively designed and ma-
nufactured for the use specified in the present
documentation. Any other use not specified in this
documentation could damage the product and be
dangerous.
• The Company declines all responsibility for any
consequences resulting from improper use of the
product, or use which is different from that expected
and specified in the present documentation.
• Do not install the product in explosive atmosphere.
• Disconnect the electrical power supply before
carrying out any work on the installation. Also
disconnect any buffer batteries, if fitted.
• Only u se o riginal parts f or a ny m aintenance or r epair
operation.
• Instruct the product user about the control systems
provided and the manual opening operation in case
of emergency.
• The user must avoid any attempt to carry out work
or repair on the automation system, and always
request the assistance of qualified personnel.
• Anything which is not expressly provided for in the
present instructions, is not allowed.
• The power supply must have a very low safety vol-
tage and the generator must be protected against
short circuit.
• All cables must be stripped close to the terminals
only.
1) GENERAL OUTLINE
Programmable digital pushbutton panel for control-
ling pedestrian and vehicle access points using two
operating methods:
1 - Serial connection:
Manages control panels provided with serial con-
INSTALLATION MANUAL
nection.
Up to 16 different codes can be memorised. Each
valid code sends a start command through the
serial line.
2 - Interfaced with a WIEGAND system:
Manages control panels provided with serial con-
nection.
he WIEGAND connection can be via expansion board
or dedicated connector.
Provided with an anti-break-in metal contai-
ner, the Q.BO PAD pushbutton panel does not
directly control access point opening. Therefore,
it can also be safely installed in unprotected
areas.
2) TECHNICAL SPECIFICATIONS
Power supply
Absorption
Working
temperature
No. codes
(serial connection):
Dimensions:
Degree of protection: IP 45
3) INSTALLATION
Use the box as a drilling template and drill 4 holes. Fix
by means of self-tapping screws or expansion plugs,
depending on the surface the box is being fixed on.
Use the black sponge (H, Fig.A1) between the appliance
and the wall (Fig.A1).
1) Proceed to wiring and fixing the electronic board
by means of the 2 screws supplied as standard,
as shown in Fig.B1. Fully tighten the screws, and
correct any centring errors using the slots in the
board. Correct board positioning is obtained by
means of the connection terminal bar, positioned
as shown in Fig.B1.
2) Position the gasket and ring nut, as shown in Fig. B2,
and proceed to fixing using the 4 screws supplied.
3) Attach the metal button unit after rotating it by
about 30° anticlockwise, as shown in Fig.B3.
4) Use the special anti-break-in setscrew wrench
supplied and loosen the dowel until it is secured
to the bottom of the push-button board (Fig.B4).
4) CONNECTION DIAGRAM
WARNING! In case the power is supplied by an external
generator, it should feature a very low safety voltage
and the generator be protected against short-circuit
and overloading.
JP1
1-2
3-4
5-6
5) DIP-SWITCHES
~
12/24 V
60 mA
-10 / +55°C
16
see Fig.A
Power supply input 12/24 V
~
1 - + 12/24 V /
2 - 0 V
Serial output towards control panels:
3-TX1 4-TX2
Data output for connection to WIEGAND:
5-DØ 6-D1
/ ±10% 50/60Hz
~
/ ±10% 50Hz
9
Q.BO PAD -