General Power Tool Safety Warnings - Tecomec SHARP Master Manual De Instrucciones

INDEX
1.

GENERAL POWER TOOL SAFETY WARNINGS ......... 7

2. GENERAL INFORMATION ............................................ 8
3. WARRANTY ................................................................... 8
4. USING AND KEEPING UP THE OWNER'S MANUAL .. 8
5. DEFINITIONS ................................................................ 8
6. SYMBOLS ...................................................................... 8
7. TECHNICAL DATA ......................................................... 9
8. PART DESCRIPTION (FIG. 1) ....................................... 9
9. SAFETY DEVICES ........................................................ 9
10. INTENDED USE ............................................................ 9
11. UNPACKING .................................................................. 9
12. STANDARD SUPPLY (FIG. 2) ....................................... 9
13. INSTALLATION .............................................................. 9
14. CHAIN INFORMATION ............................................... 10
15. CHAIN IDENTIFICATION............................................. 10
16. FITTING THE GRINDING WHEEL .............................. 10
17. SECURING THE GRINDING WHEEL GUARD ........... 10
18. ELECTRICAL CONNECTION ....................................... 10
19. START-UP .................................................................... 11
20. CHECKING THE GRINDING WHEEL ASSEMBLY ..... 11
21. ADJUSTING THE GRINDER ....................................... 11
22. SHARPENING WARNINGS ......................................... 11
23. SHARPENING THE CHAIN (FIG. 18).......................... 11
24. SHARPENING THE DEPTH GAUGE (FIG. 19)........... 12
25. STOPPING AND SHUTTING DOWN .......................... 12
26. TROUBLE SHOOTING ................................................ 12
1. GENERAL POWER TOOL SAFETY WARNINGS
WARNING Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed
below may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b) Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
EN
b) Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators. There
is an increased risk of electric shock if your body is
earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
NOTE The term "residual current device (RCD)" can
be replaced by the term "ground fault circuit interrupter
(GFCI)" or "earth leakage circuit breaker (ELCB)".
3) Personal safety
a) Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal
injury.
b) Use personal protective equipment. Always wear eye
protection. Protective equipment such as a dust mask,
non-skid safety shoes, hard hat or hearing protection
used for appropriate conditions will reduce personal
injuries.
c) Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source and/
or battery pack, picking up or carrying the tool. Carrying
power tools with your finger on the switch or energising
power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool
in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery.
Keep your hair and clothing away from moving parts.
Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of tools
allow you to become complacent and ignore tool safety
principles. A careless action can cause severe injury
within a fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the
job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
7