BFT ELI 250 BT Instrucciones De Uso página 4

Téléchargé sur www.confort-electrique.fr
ENGLISH
Thank you for buying this product, our company is sure that you will be more than satisfied with the performance of the product. This product is supplied
with a "Warnings" leaflet and an "Instruction manual". These should both be read carefully as they provide important information about safety, installation,
operation and maintenance. This product complies with recognised technical standards and safety regulations. We declare that this product is in conformity
with the following European Directives: 89/336/EEC and 73/23/EEC (and subsequent amendments).WARNINGS: Any assistance required on automation
components must be carried out by a qualified technician (installer).
1) GENERAL OUTLINE
The ELI 250 BT electromechanical actuator is the ideal solution for underground hinge-pivot installation. The actuator consists of a perfectly sealed single-
block reduction gear. The under hinge-pivot position maintains the aesthetic appearance of the gate and practically hides the automation system.
Once the bearing case is installed, the gate can be operated even without fitting the actuator which can be inserted later. When maintenance is required, this
type of case allows the actuator to be taken out without removing the gate leaf. The ELI 250 BT actuator can be fitted to any type of swing gate which meets
the values shown in the "Technical Specifications" table. The pushing force is set on the control unit (see specific manual).The end-of-stroke operation
is controlled by special end-of-stroke magnetic sensors and by mechanical stop blocks located inside the foundation case. CAUTION! The actuator mod.
ELI 250 BT is not provided with mechanical torque adjustment. It is compulsory to use a control board of the same manufacturer, according to
the basic safety requirements of directives 73/23/CEE, 89/336/CEE, 98/37/CEE and provided with adequate electric torque adjustment.
2) EMERGENCY MANOEUVRE
Emergency release is obtained by using the key provided, on the release unit which is located under the gate, on the protruding section of the lever-pivot.
To release, insert the key in the release triangle and turn it by about 90° in the direction shown by the open-padlock symbol (fig.1). If the leaf is equipped
with an electric lock, release the electric lock as well. To open/close the gate, push it manually. To restore motor-driven operation, reposition the gate by ali-
gning it with the lever bearing the lock unit, and turn the key in the direction shown by the closed-padlock symbol (fig.1) checking that engagement is correctly
restored. Keep the leaf release key (and that of the electric lock, if any) in a place which is known to the users.
3) AUTOMATION OPERATION
Since the automation system can be remotely controlled by means of a radio control device or a Start button, and therefore out of sight, all safety devices
must be frequently checked in order to ensure their perfect efficiency. In the event of any anomalous operation, request immediate assistance from qualified
personnel. Children must be kept at a safe distance from the automation operation area.
4) SCRAPPING
Materials must be disposed of in conformity with the current regulations.
In case of scrapping, the automation devices do not entail any particular risks or danger. In case of recovered materials, these should be sorted out by
type (electrical components, copper, aluminium, plastic etc.).
5) DISMANTLING
When the automation system is disassembled to be reassembled on another site, proceed as follows:
• Disconnect the power supply and the entire electrical installation.
• Remove the gearmotor from its fixing base.
• Disassemble the control panel, if separate, and all installation components.
• In the case where some of the components cannot be removed or are
damaged, they must be replaced.
6) MALFUNCTION: CAUSES AND REMEDIES
When any operational malfunction is found, and not resolved, disconnect the mains power supply and request the assistance of a qualified
technician (installer).
When automation is out of order, activate the manual release to allow the opening and closing operations to be carried out manually.
During this period of time, keep the lock in the closed position by means of a chain and padlock.
-
4
ELI 250 BT - Ver. 03
Téléchargé sur www.confort-electrique.fr
Retrouvez tous les produits du fabricant BFT sur notre site internet www.confort-electrique.fr
USER'S MANUAL
Fig. 1
2
Max. 90°
1
Retrouvez tous les produits du fabricant BFT sur notre site internet www.confort-electrique.fr