Technical Specifications; Care And Maintenance - Twiins D3 Manual De Instrucciones

Intercom pairing with a different Twi-
ins D1, Twiins D2 or a different Blue-
® ®
tooth audio receiver.
®
Dual Link: Pairing as an intercom while maintaining
hands-free functionality:
• Complete pairing with the phone as described in the
paragraph above "Pairing to a mobile phone or GPS
navigator".
• Switch off Bluetooth on the phones.
®
• Make sure both devices to be paired are switched off.
• Press and hold the control button (1b) of the Twiins
D3 device until the LED indicator begins flashing in Red
and Blue.
• Press and hold the control button (1b) of the Twiins
D1 or Twiins D2 device until the LED indicator begins
®
flashing in Red and Blue. If you are using a different de-
vice, put it in pairing mode.
• Briefly press the control button (1b) of the Twiins
device once. After a few seconds, both devices will pair
and intercom functions will be activated. Once paired,
it is recommended for you to switch off the Twiins
device and switch it back on so that it operates cor-
rectly with your phone and as an intercom.
The other intercom device will receive an acoustic warn-
ing signal.
• Activate Bluetooth on the phones again. Depend-
®
ing on the phone, it will automatically detect the device
paired. Otherwise, you will need to select it manually.
NOTE: When two Twiins
®
incoming call functionality with their respective mobile
phones will be maintained. In case a call is received,
intercom functionality will stop and resume once the call
has ended.
Single Link: Pairing as an intercom only (without
hands-free features):
• Make sure both devices are switched off.
• Press and hold the control button (1b) of the Twiins
D3 device until the LED indicator begins flashing in Red
and Blue.
• Press and hold the control button (1b) of the Twiins
D1 or Twiins D2 device until the LED indicator begins
®
flashing in Red and Blue. If you are using a different de-
vice, put it in pairing mode.
devices are in intercom mode,
• Briefly press the control button (1b) of the Twiins
device once. After a few seconds, both devices will pair
and intercom functions will be activated. Once paired,
it is recommended for you to switch off the Twiins
device and switch it back on so that it operates cor-
rectly with your telephone and as an intercom.
The other intercom device will receive an acoustic warn-
ing signal.
Intercom functions:
Activating and deactivating intercom functions be-
tween two Twiins® devices: once both Twiins
®
have been paired and switched on, press the control
button (1b) of the Twiins
or deactivate intercom functionality.
®
Adjusting the volume for intercom functions: you can
adjust the volume by briefly pressing the control button
(1b). It will then cycle through three levels: LOW < ME-
D3 DIUM < HIGH < LOW...
®

Technical Specifications

D3 Bluetooth : 2.1 Class 2
® ®
Profiles: A2DP stereo, HSP, HFP, EDR
Intercom frequency: 2.4 GHz
Battery: Lithium polymer, allowing for up to 7 hours of
talk time and 200 hours of standby time (depending on
use and configuration of the device)

Care and maintenance

The Twiins D3 device uses components with the lat-
®
est technology and is manufactured to high standards.
To keep your device from inadvertently becoming dam-
aged, please read the following recommendations care-
fully:
• Do not attempt to open any of the system compo-
nents, since the electronic parts inside it may become
damaged. Do not attempt to open or change the bat-
tery as it may be dangerous.
• Keep the Twiins
• Keep the Twiins
®
densation may damage the electronic circuits.
• Avoid exposing the device to extreme temperatures.
Intense cold may create condensation inside the com-
®
ponents as these warm up. Extreme heat may damage
the battery, circuits or casings.
• Do not drop, hit or bend the components as the inter-
D3 for two seconds to activate
®
D3 out of the reach of children.
®
D3 in a dry place. Humidity and con-
®
D3
®
D3
®
devices
®
11