BWT Infinity A Instrucciones De Montaje página 15

0 0 0
Σ m
3
1. 1. 1. 1. 1.
3. 3. 3. 3. 3.
> 400 mm > 400 mm > 400 mm
> 400 mm > 400 mm
5 5 5 5 5
6 6 6 6 6
> 1 m > 1 m > 1 m
> 1 m > 1 m
2. 2. 2. 2. 2.
4. 4. 4. 4. 4.
> 20 mm > 20 mm > 20 mm
> 20 mm > 20 mm
Installation Installation
Installation Installation Installation
Caution! Do not plug in the transformer with Caution! Do not plug in the transformer with Caution! Do not plug in the transformer with Caution! Do not plug in the transformer with Caution! Do not plug in the transformer with
plug (3) until startup. plug (3) until startup. plug (3) until startup.
plug (3) until startup. plug (3) until startup.
Install the filter in the cold water pipes upstream of
the objects to be protected (see installation dia-
gram). Always provide stop valves.
Install the connecting module or connector in the
direction of flow in a horizontal or vertical cold wa-
ter pipe (observe direction of flow arrow).
Connection to connecting module / DR 3/4" - Connection to connecting module / DR 3/4" - Connection to connecting module / DR 3/4" - Connection to connecting module / DR 3/4" - Connection to connecting module / DR 3/4" -
1 1/4" 1 1/4"
1 1/4" 1 1/4" 1 1/4"
1. Turn the red retaining ring to the left limit stop.
2. Press the prongs of the device into the spaces
provided
3. and rotate the device clockwise 45° to the limit
stop.
4. Pull the red retaining ring with both hands to-
wards the device until it clicks into place. The
device cannot now be rotated unintentionally.
To release the filter, press the retaining ring to-
wards the connecting module.
Connecting to connector / HWS 1 1/2" and 2" Connecting to connector / HWS 1 1/2" and 2" Connecting to connector / HWS 1 1/2" and 2" Connecting to connector / HWS 1 1/2" and 2" Connecting to connector / HWS 1 1/2" and 2"
Screw the filter to the connector using 4 hexagon
screws and the seal (screws and washers in-
cluded).
Check the seal for proper fit. Tighten the screws
evenly and crosswise.
Wastewater connection Wastewater connection Wastewater connection Wastewater connection Wastewater connection
Route the wastewater connection to the drain so
that no reflux occurs.
Note: Do not bend the vent tube (5 5 5 5 5 ) when chang-
ing to the hose connection (6 6 6 6 6 ).
Please note: According to DIN 1988, the flush- Please note: According to DIN 1988, the flush- Please note: According to DIN 1988, the flush- Please note: According to DIN 1988, the flush- Please note: According to DIN 1988, the flush-
ing water hose must be secured at a distance ing water hose must be secured at a distance ing water hose must be secured at a distance
ing water hose must be secured at a distance ing water hose must be secured at a distance
of at least 20mm from the highest possible of at least 20mm from the highest possible of at least 20mm from the highest possible of at least 20mm from the highest possible of at least 20mm from the highest possible
waste water level (free discharge). waste water level (free discharge). waste water level (free discharge).
waste water level (free discharge). waste water level (free discharge).
GB GB GB GB GB
15 15 15 15 15