Scope Of Use; Assembly And Starting - Stanley D 200/8 Serie Manual De Instrucciones

● When fitting a tool, the flow of air in output must be
switched off.
● When using compressed air, you must know and
comply with the safety precautions to be adopted for
each type of application (inflation, pneumatic tools,
painting, washing with water-based detergents only,
etc.).
2. LAYOUT (FIG. 1)
1. Shroud
2. Pressure vessel
3. Wheel
4. Supporting foot
5. Quick-lock coupling (regulated compressed air)
6. Pressure gauge (for reading the preset pressure by
means of the pressure regulator)
7. Pressure regulator
8. I/O switch (ON/OFF)
9. Transportation handle
10. Safety valve
11. Drain valve
12. Pressure gauge (for reading the tank pressure)
13. Axle
14. Clip
15. Screw
16. Nut
17. Washer

3. SCOPE OF USE

The compressor is designed for generating compressed
air for tools operated by compressed air.
Please note that our equipment has not been designed
for use in commercial, trade or industrial applications.
Our warranty will be voided if the machine is used
in commercial, trade or industrial businesses or for
equivalent purposes.
The machine is to be used only for its prescribed purpose.
Any other use is deemed to be a case of misuse. The user/
operator and not the manufacturer will be liable for any
damage or injuries of any kind caused as a result of this.
4. POINTS TO NOTE WHEN SETTING
UP THE COMPRESSOR
● Examine the machine for signs of transit damage.
Report any damage immediately to the company which
delivered the compressor.
● The compressor should be set up near the working
consumer.
● Avoid long air lines and long supply lines (extensions).
● Make sure the intake air is dry and dust-free.
● Do not set up the compressor in damp or wet rooms.
● Please check that the air consumption and the maximum
working pressure of the pneumatic tool and connection
pipes (with the compressor) to be used, are compatible
with the pressure set on the pressure regulator and with
the amount of air supplied by the compressor.
● The compressor may only be used in suitable rooms (with
good ventilation and an ambient temperature from +5°C to
+40°C). There must be no dust, acids, vapors, explosive
gases or inflammable gases in the room.
● The compressor is designed to be used in dry rooms. It
is prohibited to use the compressor in areas where work
is conducted with sprayed water.

5. ASSEMBLY AND STARTING

Warning!
You must fully assemble the appliance before
using it for the first time.
5.1 Fitting the wheels (Fig. 3, 4, 5 & 6)
Fit the supplied wheels as shown in Fig. 3, 4, 5 & 6:
●
Fig. 3a & 3b: Assembly of wheel kit - version A
Assembly by sequence: a, b, c, d, e
● Fig. 4a & 4b:
Assembly of wheel kit - version B
● Fig. 5:
Assembly of wheel kit - version C
● Fig. 6:
Assembly of wheel kit - version D
5.2 Fitting the supporting foot (ref. 4)
Fit the supplied rubber stopper as shown in Fig. 7.
5.3 Voltage
The compressor is equipped with a mains cable with
shock-proof plug. Insert the plug of the electric cable
in a socket of suitable shape, voltage and frequency
complying with current regulations. Before you use the
machine, make sure that the mains voltage complies
with the specifications on the rating plate. Long supply
cables, extensions, cable reels etc. cause a drop in
voltage and can impede motor start-up. In the case of low
temperatures below +5°C, motor start-up is jeopardized as
a result of stiffness.
5.3.1 Connection of the mains plug (electrical
information for the BS plug)
Important!
The wires in the mains lead fitted to this product are
coloured in accordance with the code shown in fig. 8.
● The 3 pin plug must comply to BS1363/A.
● Fuse must comply to BS1362.
23
G
B