Assembly And Starting; Scope Of Use - Stanley BA 550/11/200 Manual De Instrucciones

position and then to ON again (figures 2a & 2b).
● Operate manually on the button of the pressure
switch, returning this to the ON position, or press
the button of the thermal cutout inside the box of the
electric panel (figure 2d).
● To guarantee machine safety, all the compressors
are fitted with a safety valve (ref. 10) that is activated
in the case of failure of the pressure switch.
● All two-stage compressors are equipped with safety
valves on the air delivery manifold to the reservoir
2. LAYOUT
1. Intake air filter
2. Pressure vessel
3. Wheel
4. Guide roller (or vibration-damper)
5. Quick-lock coupling (regulated compressed air)
6. Pressure gauge (for reading the preset tank pressure)
7. Pressure regulator
8. ON/OFF switch
9. Transportation handle
10. Safety valve
11. Drainage screw for condensation water
12. Pressure gauge (for reading the tank pressure)
13. Quick-lock coupling (unregulated compressed air)
14. Oil sealing plug (oil filler opening)
15. Oil drainage screw
16. Oil level window
17. Bolt
18. Nut
19. Washer
20. Check valve
21. Tap ball valve

3. SCOPE OF USE

The compressor is designed for generating compressed
air for tools operated by compressed air.
The machine is to be used only for its prescribed pur-
pose. Any other use is deemed to be a case of misuse.
The user / operator and not the manufacturer will be
liable for any damage or injuries of any kind caused as
a result of this.
4. POINTS TO NOTE WHEN SETTING
UP THE COMPRESSOR
● Examine the machine for signs of transit damage.
Report any damage immediately to the company
which delivered the compressor.
● The compressor should be set up near the working
consumer.
and on the connection hose between the low and high
pressure located on the head. These are activated in
the case of malfunctioning (fig. 3a-3b).
● When fitting a tool, the flow of air in output must be
switched off.
● When using compressed air, you must know and
comply with the safety precautions to be adopted for
each type of application (inflation, pneumatic tools,
painting, washing with water-based detergents only,
etc.).
● Avoid long air lines and long supply lines (exten-
sions).
● Make sure the intake air is dry and dust-free.
● Do not set up the compressor in damp or wet rooms.
● The compressor may only be used in suitable rooms
(with good ventilation and an ambient temperature from
+5°C to +40°C). There must be no dust, acids, vapors,
explosive gases or inflammable gases in the room.
● The compressor is designed to be used in dry rooms.
It is prohibited to use the compressor in areas where
work is conducted with sprayed water.
● The oil level in the compressor pump has to be
checked before putting the equipment into operation.
● Check for correspondence between the compressor
plate data with the actual specifications of the electri-
cal system. A variation of ± 10% with respect of the
rated value is allowed.
● Check the oil level using the sight glass and if neces-
sary unscrew the vent plug and top up (see figures
13a-13b-14a-14b).

5. ASSEMBLY AND STARTING

Warning!
You must fully assemble the appliance before us-
ing it for the first time.
5.1 Fitting the wheels (figs. 4-5)
Fit the supplied wheels as shown in figures 4 and 5.
5.1.1 Fitting the supporting feet (fig. 6)
Fit the supplied vibration-dampers as shown in fig. 6.
5.2 Fitting the quick-lock coupling for
tank pressure (figs. 7-8)
Screw the quick-lock coupling for unregulated tank pres-
sure (ref. 13) to the pressure vessel (ref. 2) as shown in
figures 7 and 8.
5.2.1 Fitting the tap ball valve (fig. 9)
If provided, fit the tap ball valve as shown in figure 9.
25
G
B